THOMSON MEC 320, Operating Manual

Page: 71 / 93

MEC 320 GENSET CONTROLLER
PM079 Rev 0 07/06/08 71 Thomson Technology
Overview list
Protection 4410 Wire failure VDO input 104 p.83
1010 Reverse power p.72 4420 Wire failure VDO input 105 p.83
1020 Overcurrent 1 p.72 4430 Wire failure VDO input 106 p.84
1030 Overcurrent 2 p.72
Output setup
Synchronization
5090 Relay 9 p.85
2010 Synchronization type p.73 5100 Relay 10 p.85
2020 Dynamic Synchronization p.73 5110 Relay 11 p.85
2030 Static Synchronization p.73 5120 Relay 12 p.85
2040 Sync. blackout p.73 5130 Relay 13 p.85
2070 GB general failure p.74 5490 Transistor setup p.85
2080 MB general failure p.74
2090 Breaker failure alarms p.74
General setup
2100 Separate Synchronization relay p.74 6010 Nominal settings 1 p.86
2110 Close before excitation p.74 6020 Nominal settings 2 p.86
2120
Breaker sequence
p.75 6030 Transformer gen. p.86
2130 Excitation failure p.75 6040 Transformer bus. p.86
6050 Engine type p.86
Regulation 6060 Gen-set modes p.87
2510 Frequency controller p.76 6070 Date and time (internal clock) setting p.87
2520 Power controller p.76 6080 Counters p.87
2530 Power ramp up p.76 6090 Service timer p.87
2540 Power ramp down p.76 6110 Battery low voltage alarm p.88
2560 Governor regulation failure p.76 6120 Battery high voltage alarm p.88
2640 Relay control p.77 6130 Language p.88
2690 Delay regulation p.77 6140 Alarm horn p.88
2700 Short time paralleling p.77 6150 Running status p.88
6160 Remove starter p.88
Binary input setup 6170 Starter p.88
3260 Dig. input no. 110 p.78 6180 Start attempts p.89
3270 Dig. input no. 111 p.78 6190 f/U OK p.89
3280 Dig. input no. 112 p.78 6200 f/U failure p.89
3290 Dig. input no. 113 p.78 6210 Stop p.89
3300 Access lock (binary input 114) p.78 6220 Stop failure p.89
3310 Running feedback (binary input 115) p.79 6250 GB control p.89
3320 Ext. engine failure (binary input 116) p.79 6260 Pnom derate p.89
3330 Ext. emergency stop (binary input 117) p.79 6310 Idle running p.90
3340 Dig. input no. 118 p.79 6400 Master clock p.90
6410 Battery test p.90
Analogue input setup 6420 Voltage trip p.90
4090 4…20mA input 98.1 p.80
4100 4…20mA input 98.2 p.80 Mains setup
4110 Oil pressure 1 (4…20mA input 100.1) p.80 6500 Mains power p.91
4120 Oil pressure 2 p.80 6510 Daytime period p.91
4130 Fuel level 1 (4…20mA input 102.1) p.81 6520 Start gen-set p.91
4140 Fuel level 2 p.81 6530 Stop gen-set p.91
4170 VDO 104.1 p.81 6540 Test running p.91
4180 VDO 104.2 p.81 6550 Fixed power set point p.91
4190 VDO 105.1 p.81 6590 Mains failure voltage p.92
4200
VDO 105.2 p.82 6600 Mains failure frequency p.92
4210 VDO 106.1 p.82 6610 Mains breaker control p.92
4220 VDO 106.2 p.82
4300 Running detection p.82 Jump menus
4310 Overspeed 1 p.82 9000 Software version p.93
4320
Overspeed 2 p.83 9020 Service port p.93
4370 Wire failure analogue input 98 p.83 911X User password p.93
4380 Wire failure analogue input 100 p.83 9120 Service menu p.93
4390 Wire failure analogue input 102 p.83 9130 Single phase/split phase/three phase p.93