Thecus N12000 series User Manual Download Page 76 | Manualshive

Page: 76 / 120

background image

76

Hostname

Enter the name or IP address of the host

Privilege

Host has either read only or writeable access to the folder.

OS Support

There are two selections available:



Unix / Linux System



AIX (Allow source port > 1024)

Choose the one which best fits your needs.

ID Mapping

There are three selections available:



Guest system root account will have full access to this
share (root:root).



Guest system root account will be mapped to anonymous
user (nobody:nogroup) on NAS.



All user on guest system will be mapped to anonymous
user (nobody:nogroup) on NAS.

Choose the one which best fits your needs.

Sync / Async

Choose to determine the data “Sync” at once or “Async” in
arranged batch.

Apply

Click to save your changes.

Folder and sub-folders Access Control List (ACL)

On the Folder screen, press the ACL button, and the ACL setting screen appears.
This screen allows you to configure access to the specific folder and sub-folders for
users and groups. Select a user or a group from the left hand column and then
choose Deny, Read Only, or Writable to configure their access level. Press the
Apply button to confirm your settings.

«
...
74
75
76
77
78
...
»

Summary of Contents for N12000 series

























































































































Reviews:

No comments

Related manuals for N12000 series

Brand: DB GROUP HERRAJES Pages: 4

Brand: NEC Pages: 59

Brand: Campbell Pages: 32

Brand: Quantum Pages: 32

Brand: Data General Pages: 58

Mobile Ultra Memory Stick Micro

Brand: SanDisk Pages: 1

WD Caviar Green WD10EADS

Brand: Western Digital Pages: 2

Brand: DataWhale Pages: 31

Brand: Teknim Pages: 10

digitalSTROM-Server

Brand: aizo Pages: 2

Brand: Angel Cool Pages: 2

Brand: Eaton Pages: 2

Brand: Ubiquiti Pages: 23

Brand: Lantronix Pages: 75

Brand: Ubiquiti Pages: 20

TE100S8P - Fast Ethernet Switch

Brand: TRENDnet Pages: 11

Brand: Planet Pages: 66

Brand: TYANO Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands