Thecus N12000 series User Manual Download Page 13

Page: 13 / 120

Rear Panel

N16000 series:

The N16000 rear panel features ports and connectors.

Back Panel

Item

Description

1.Power Connector



Connect the included power cords to these connectors

2.Serial Port



This port is for external UPS device

3.eSATA Port



eSATA port for high-speed storage expansion

4.USB Port



USB 2.0 port for compatible USB devices, such as USB disks, and
USB printers

5.USB Port



USB 3.0 port for compatible USB devices.

6.WAN/LAN1 Port



WAN/LAN1 port for connecting to an Ethernet network through a
switch or router

7.LAN2 Port



WAN/LAN1 port for connecting to an Ethernet network through a
switch or router

8.LAN3 Port



LAN3 port for HA connecting.

Summary of Contents for N12000 series

























































































































Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands

Thecus N12000 series, User Manual

Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands