Thecus N12000 series User Manual Download Page 47

Page: 47 / 120

HA Standby Unit:

The Standby unit has no accessibility as its roll played.

HA Configuration

Item

Description

High-Availability

Enable HA Service on the Thecus IP storage.

Role

Set Thecus IP Storage as Active or Standby mode

Virtual Hostname

Name of the Virtual Server

Virtual IP

The IP address of your Virtual Server

Network Configuration

Active Server
Hostname

Name of the Active Server.

Active Server LAN1 IP

The IP address of your Active Server

Standby Server
Hostname

Name of the Standby Server.

Standby Server LAN1
IP

The IP address of your Standby Server

iSCSI-Block Configuration

LAN3 MAC

The MAC address of the LAN3

Active Server LAN3 IP

The IP address of your Active Server (needs to set the same
segment with Standby Server)

Standby Server LAN3
IP

The IP address of your Standby Server (needs to set the same
segment with Active Server)

Summary of Contents for N12000 series

























































































































Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands

Thecus N12000 series, User Manual

Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands