Thecus N12000 series User Manual Download Page 37

Page: 37 / 120

LAN2 Configuration

Item

Description

MAC Address

Displays the MAC address of the LAN2 interface.

Jumbo Frame Support

Enable or disable Jumbo Frame Support on the LAN2 interface.

Specifies the IP address of the LAN2 interface.

Netmask

Specifies the Network Mask of the LAN2 interface.

Gateway

When Thecus NAS as a DHCP server from LAN2, it can have
another route to balance traffic bandwidth for its DHCP
clients

Link Detected

Specifies the LAN2 port link status

Lick Speed

Specifies the LAN2 port link speed

DHCP Server Configuration

A DHCP server can be configured to assign IP addresses to devices connected to the
LAN2 port. To configure these ports, choose LAN2 from the System Network
menu.

DHCP Configuration

Item

Description

DHCP Server

Enable or disable the DHCP server to automatically assign IP
address to PCs connected to the LAN2 interface.

Start IP

Specifies the starting IP address of the DHCP range.

End IP

Specifies the ending IP address of the DHCP range.

DNS Server

Displayed the DNS server IP address.

NOTE

Before enabling Jumbo Frame Support, please make sure your network equipment

supports Jumbo Frame. If your equipment is incompatible, you might not be able to

connect to your Thecus IP storage.

NOTE

If the IP sharing mode setting is set to “Enable” under WAN/LAN21 port, then this 2

gateway cannot be configured.

Summary of Contents for N12000 series

























































































































Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands

Thecus N12000 series, User Manual

Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands