Thecus N12000 series User Manual Download Page 88

Page: 88 / 120

A description of each item follows:

ADS/NT Support

Item

Description

Work Group / Domain
Name

Specifies the SMB/CIFS Work Group / ADS Domain Name (e.g.
MYGROUP).

ADS/NT Support

Select Disable to disable authentication through Windows Active
Directory Server or Windows NT.

Authentication Method

Select ADS for Windows Active Directory Server, or select NT for
Windows NT

ADS/NT Server Name

Specifies the ADS/NT server name (e.g. adservername).

ADS/NT Realm

Specifies the ADS/NT realm (e.g. example.com).

Administrator ID

Enter the administrators ID of Windows Active Directory or
Windows NT, which is required for Thecus IP storage to join
domain.

Administrator
Password

Enter the ADS/NT Administrator password.

Apply

To save your settings.

To join an AD domain, you can refer
the figure and use the example below
to configure the Thecus IP storage for
associated filed input:

Summary of Contents for N12000 series

























































































































Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands

Thecus N12000 series, User Manual

Search results

Summary of Contents for N12000 series

Reviews:

Related manuals for N12000 series

Brands by name

Popular brands