TEXIO PU100-7.5, Instruction Manual

Page: 14 / 74

4
2. SPECIFICATIONS
2.1. OUTPUT RATING
MODEL 6-100 8-90 12.5-60 20-38 30-25 40-19 60-12.5 80-9.5
100-7.
5
150-5 300-2.5 600-1.3
1.Rated output voltage (*1) V 6 8 12.5 20 30 40 60 80 100 150 300 600
2.Rated output current (*2) A 100 90 60 38 25 19 12.5 9.5 7.5 5 2.5 1.3
3.Rated output power W 600 720 750 760 750 760 750 760 750 750 750 780
2.2. INPUT CHARACTERISTICS
V 6 8 12.5 20 30 40 60 80 100 150 300 600
1.Input voltage/freq. (*3) - 85～265V AC continuous, 47～63Hz, single phase.
2.Input current
(at 100/200V AC)
A 10.5/5
3.Power Factor - 0.99@100/200V AC、rated output power.
4.Efficiency (*4) % 76/78 77/80 81/84 82/85 82/85 83/87 83/87 83/87 83/87 83/87 83/87 83/87
5.Inrush current at 100/200V A Less than 25A.
2.3. CONSTANT VOLTAGE MODE
V 6 8 12.5 20 30 40 60 80 100 150 300 600
1.Max. Line regulation (*5) - 0.01% of rated output voltage ＋2mV
2.Max Load regulation (*6) - 0.01% of rated output voltage ＋2mV
3.Ripple and noise(p-p,20MHz)
(Following 30 minutes
warm-up).
mV 60 60 60 60 60 60 60 80 80 100 150 300
4.Ripple r.m.s., 5Hz～1MHz
(Following 30 minutes
warm-up.)
mV 8 8 8 8 8 8 8 8 8 10 25 60
5.Temperature coefficient ppm/℃ 100ppm/℃ from rated output voltage, following 30 minutes warm-up.
6.Temperature drift - 0.05% of rated Vout over 8hours interval following 30 minutes warm-up. Constant line, load & temp.
7.Rem.sense compensation/wire V 1 1 1 1 1.5 2 3 4 5 5 5 5
8.Up-prog. response time,
0～Vomax (*9)
mS 90 120 150 250
9.Down-prog .response time:
Full load (*10)
mS 10 50 80 150 250
No load (*11) mS 500 600 700 900 1000 1100 1200 1400 1700 2400 3000 4800
10.Transient response time
mS
Time for the output voltage to recover within 0.5% of its rated output for a load change 10～90% of rated
output current.
Output set-point: 10～100%.
Less than 1mS, for models up to and including 100V. 2mS, for models above 100V.
11.Hold-up time mS More than 20mS, 100V AC, rated output power.
2.4. CONSTANT CURRENT MODE
V 6 8 12.5 20 30 40 60 80 100 150 300 600
1.Max. Line regulation (*5) - 0.01% of rated output current ＋2mA
2.Max. Load regulation (*7) - 0.02% of rated output current ＋5mA
3.Ripple r.m.s. 5Hz～1MHz(*8) mA 200 180 120 76 63 48 38 29 23 18 13 8
4.Temperature coefficient ppm/℃ 100ppm/℃ from rated output current, following 30 minutes warm-up.
5.Temperature drift - 0.05% of rated Iout over 8hours interval following 30 minutes warm-up. Constant line, load & temp.
2.5. ANALOG PROGRAMMING AND MONITORING
1. Vout voltage programming --- 0～100%, 0～5V/0～10V, user select. Accuracy and linearity: +/-0.5% of rated Vout.
2. Iout voltage programming --- 0～100%, 0～5V/0～10V, user select. Accuracy and linearity: +/-1% of rated Iout.