manualshive.com logo in svg

Texas Instruments TMS320DM357, User Manual

The Texas Instruments TMS320DM357 is a cutting-edge digital media processor. Unlock its full potential with our comprehensive User Manual, available for free download at manualshive.com. This manual provides detailed instructions, empowering you to harness the capabilities of this exceptional product effortlessly.

Share
Download
background image

2.3.7 Linking Transfers

2.3.7.1

Constant Addressing Mode Transfers/Alignment Issues

www.ti.com

Parameter RAM (PaRAM)

The EDMA3CC provides a mechanism known as linking, which allows the entire PaRAM set to be
reloaded from a location within the PaRAM memory map (for both DMA and QDMA channels). Linking is
especially useful for maintaining ping-pong buffers, circular buffering, and repetitive/continuous transfers
all with no CPU intervention. Upon completion of a transfer, the current transfer parameters are reloaded
with the parameter set pointed to by the 16-bit link address field (of the current parameter set). Linking
only occurs when the STATIC bit in OPT is cleared to 0.

Note:

A transfer (DMA or QDMA) should always be linked to another useful transfer. If it is required
to terminate a transfer, the transfer should be linked to a NULL set.

The link update occurs after the current PaRAM set event parameters have been exhausted. An event's
parameters are exhausted when the EDMA3 channel controller has submitted all the transfers associated
with the PaRAM set.

A link update occurs for null and dummy transfers depending on the state of the STATIC bit in OPT and
the LINK field. In both cases (null or dummy), if the value of LINK is FFFFh then a null PaRAM set (with all
0s and LINK set to FFFFh) is written to the current PaRAM set. Similarly, if LINK is set to a value other
than FFFFh then the appropriate PaRAM location pointed to by LINK is copied to the current PaRAM set.

Once the channel completion conditions are met for an event, the transfer parameters located at the link
address are loaded into the current DMA or QDMA channel’s associated parameter set. The EDMA3CC
reads the entire PaRAM set (8 words) from the PaRAM set specified by LINK and writes all 8 words to the
PaRAM set associated with the current channel.

Figure 2-8

shows an example of a linked transfer.

Any PaRAM set in the PaRAM can be used as a link/reload parameter set. The PaRAM sets associated
with peripheral synchronization events (see

Section 2.6

) should only be used for linking if the

corresponding events are disabled.

If a PaRAM set location is mapped to a QDMA channel (by QCHMAP

n

), then copying the link PaRAM set

onto the current QDMA channel PaRAM set is recognized as a trigger event and is latched in QER since a
write to the trigger word was performed. This feature can be used to create a linked list of transfers using
a single QDMA channel and multiple PaRAM sets.

Link-to-self transfers replicate the behavior of autoinitialization, which facilitates the use of circular
buffering and repetitive transfers. After an EDMA3 channel exhausts its current PaRAM set, it reloads all
the parameter set entries from another PaRAM set, which is initialized with values identical to the original
PaRAM set.

Figure 2-9

shows an example of a linked-to-self transfer. In

Figure 2-9

, parameter set 127

has the LINK field address pointing to the address of parameter set 127 (4FE0h), that is, linked-to-self.

Note:

If the STATIC bit in OPT is set for a PaRAM set, then link updates are not performed.

If either SAM or DAM is set to 1 (constant addressing mode), then the source or destination address must
be aligned to a 256-bit aligned address, respectively, and the corresponding BIDX should be an even
multiple of 32 bytes (256 bit). The EDMA3CC does not recognize errors here but the EDMA3TC asserts
an error, if this is not true. See

Section 2.11.2

.

Note:

Constant (CONST) addressing mode has limited applicability. The EDMA3 should be
configured for CONST mode (SAM/DAM = 1) only if the transfer source or destination
(on-chip memory, off-chip memory controllers, slave peripherals) support constant
addressing mode.

See the device-specific data manual to verify if constant addressing mode is supported. If
constant addressing mode is not supported, the similar logical transfer can be achieved
using INCR mode (SAM/DAM = 0) by appropriately programming the count and indices
values.

SPRUG34 – November 2008

EDMA3 Architecture

35

Submit Documentation Feedback

Summary of Contents for TMS320DM357








































































































































































Reviews:

No comments

Related manuals for TMS320DM357

Ubiquiti M900 Quick Start Manual preview
M900
Brand: Ubiquiti Pages: 24
ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
Broadcom Brocade X6-8 Director Hardware Installation Manual preview
Brocade X6-8 Director
Brand: Broadcom Pages: 207
Omega OMB-DAQBOARD-3000 Series User Manual preview
OMB-DAQBOARD-3000 Series
Brand: Omega Pages: 108
Altera DE2-70 User Manual preview
DE2-70
Brand: Altera Pages: 93
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
Ubiquiti PBE-5AC-300-ISO Quick Start Manual preview
PBE-5AC-300-ISO
Brand: Ubiquiti Pages: 28
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Brand: Sans Digital Pages: 9
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Brand: Smacq Technologies Pages: 22
Dave Embedded Systems diDo Hardware Manual preview
diDo
Brand: Dave Embedded Systems Pages: 79
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
NovaStar Nova M3 MFN300 Operation Manual preview
Nova M3 MFN300
Brand: NovaStar Pages: 16

Brands by name

Popular brands

Load more brands