Terex Genie SX-105 XC Operator'S Manual Download Page 67

Page: 67 / 76

First Edition • Third Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1270327GT

™

-105 XC

™

• SX

™

-125 XC

™

Lifting Instructions (option 2)

Fully extend the axles. Fully lower and retract the
boom. Fully lower the jib.

Remove all loose items on the machine.

Determine the center of gravity of your machine
using the table and the picture on this page.

Attach the rigging only to the designated lifting
points on the machine.

There are four lifting points on the drive chassis,
one lifting point on each axle, and two lifting points
on the riser plate of the swing chassis.

Adjust the rigging to prevent damage to the
machine and to keep the machine level.

Center of gravity

X Axis (1) Y Axis (2)

SX-105 XC

79 in

2.0 m

47 in

1.2 m

SX-125 XC

83 in

2.1 m

51 in

1.3 m

Summary of Contents for Genie SX-105 XC













































































Search results

Summary of Contents for Genie SX-105 XC

Reviews:

Related manuals for Genie SX-105 XC

Brands by name

Popular brands

Terex Genie SX-105 XC, Operator'S Manual

Search results

Summary of Contents for Genie SX-105 XC

Reviews:

Related manuals for Genie SX-105 XC

Brands by name

Popular brands