manualshive.com logo in svg

Terex Genie SX-105 XC, Operator'S Manual, Page: 66 / 76

Share
Download
Terex Genie SX-105 XC Operator'S Manual Download Page 66

Operator's Manual

 

First Edition • Third Printing

 

Transport and Lifting Instructions 

 

 

64 

SX

™

-105 XC

™

 

• SX

™

-125 XC

™

 

Part No. 1270327GT 

 

 

Observe and Obey: 

 

Only qualified riggers should rig the machine. 

 

Only certified crane operators should lift the 
machine and only in accordance with the 
applicable crane regulations. 

 

Be sure the crane capacity, loading surfaces 
and straps or lines are sufficient to withstand 
the machine weight. See the serial label for 
the machine weight. 

Lifting Instructions (option 1) 

Fully extend the axles. Fully lower and retract the 
boom. Fully lower the jib. 

Remove all loose items on the machine. 

Determine the center of gravity of your machine 
using the table and the picture on this page. 

Attach the rigging only to the designated lifting 
points on the machine.   

There are four lifting points on the drive chassis, 
one lifting point on each axle, and two lifting points 
on the riser plate of the swing chassis. 

Adjust the rigging to prevent damage to the 
machine and to keep the machine level. 

Center of gravity 

X Axis 

Y Axis 

SX-105 XC 

116 in 

2.9 m 

58 in 

1.5 m 

SX-125 XC 

131 in 

3.3 m 

62 in 

1.6 m 

 

 

 

 

Summary of Contents for Genie SX-105 XC













































































Reviews:

No comments