manualshive.com logo in svg

Terex Genie SX-105 XC, Operator'S Manual, Page: 53 / 76

Share
Download
Terex Genie SX-105 XC Operator'S Manual Download Page 53

First Edition • Third Printing

 

Operator's Manual

 

 

Operating Instructions 

 

 

Part No. 1270327GT

 

SX

™

-105 XC

™

 

• SX

™

-125 XC

™

 

51 

 

 

Operating Envelope Indicator Lights 

The operating envelope indicator lights will come 
on to notify the operator that a function has been 
interrupted and/or an action is required by the 
operator. 

Raise/Retract Boom indicator 
light flashing: Raise/retract the 
boom until the indicator light is 
off. 

 

Lower Boom indicator light 
flashing: Lower the boom until 
the indicator light is off. 

 

Machine Not Level indicator 
light flashing: The tilt alarm will 
be sounding when this light is 
flashing. Move the machine to a 
firm, level surface. 

 

 

 

 

If the tilt alarm sounds with the 
platform uphill: 

1

 

Lower the boom. 

2

 

Retract the boom. 

 

If the tilt alarm sounds with the 
platform downhill: 

1

 

Retract the boom. 

2

 

Lower the boom. 

 
 

Platform Not Level indicator 
light flashing: The tilt alarm will 
be sounding when this light is 
flashing. The Platform Level 
toggle switch will only work in 
the direction that will level the 
platform. Level the platform 
until the indicator light is off. 

 

Summary of Contents for Genie SX-105 XC













































































Reviews:

No comments