Terex Genie SX-105 XC Operator'S Manual Download Page 60

Page: 60 / 76

Operator's Manual

First Edi

tion • Third Printing

Operating Instructions

™

-105 XC

™

• SX

™

-125 XC

™

Part No. 1270327GT

LCD Screen (if equipped)

The LCD screen displays hour meter, voltage, oil
pressure and coolant temperature. The screen
also displays fault codes and other service
information.

Perkins Engine

Machines equipped with Perkins 854F-34T Diesel
engines have a regeneration mode that should run
automatically when needed.

LCD will display REGEN FORCED and WARNING
HIGH EXHAUST SYSTEM TEMP when the
regeneration mode is running. No service required.

Pipe Cradle Instructions

The pipe cradle assembly consists of 2 pipe
cradles positioned at either side of the platform
and mounted to the guardrails with U-bolts.

strap

U-bolts

pipe cradle mount

upper platform railing

pipe cradle weldment

middle platform railing

flat washers

nylock nuts

Summary of Contents for Genie SX-105 XC













































































Search results

Summary of Contents for Genie SX-105 XC

Reviews:

Terex Genie SX-105 XC, Operator'S Manual, Page: 60 / 76

Search results

Summary of Contents for Genie SX-105 XC

Reviews: