Terex Genie SX-105 XC Operator'S Manual Download Page 4

Page: 4 / 76

Operator's Manual

First Edition • Third Printing

Introduction

™

-105 XC

™

• SX

™

-125 XC

™

Part No. 1270327GT

Platform controls symbology and related
machine movement:

Platform level

Platform rotate

Jib boom up/down

Boom up/down

Boom extend/retract

Turntable rotate

Drive forward/reverse

Steer right/left

Ground controls symbology and related
machine movement:

Platform level, jib boom
up/down, boom
extend/retract,and boom
up/down

Turntable rotate and
platform rotate

Sequential functions and movement:



Drive and steer.

Interlocked functions:



Elevated drive speed.



Elevated drive in an off-level condition.



Drive enable when the boom is rotated past the
non-steer wheels.



All platform and ground controls.

Limitations of use:



The intended use of this machine is to lift
personnel, including tools, and materials to an
aerial work site.



Do not elevate the platform unless the machine
is on firm level ground.

Stability enhancing means:



Foam filled tires (if equipped).

Restricted operating envelope:



1,000 lbs/454 kg platform capacity.

Summary of Contents for Genie SX-105 XC













































































Search results

Summary of Contents for Genie SX-105 XC

Reviews:

Related manuals for Genie SX-105 XC

Brands by name

Popular brands

Terex Genie SX-105 XC, Operator'S Manual

Search results

Summary of Contents for Genie SX-105 XC

Reviews:

Related manuals for Genie SX-105 XC

Brands by name

Popular brands