Terasic T-Core User Manual Download Page 43

Page: 43 / 66

T-Core
User Manual

www.terasic.com

January 14, 2020

Create a file named /etc/udev/rules.d/51-usbblaster.rules.

Add the following lines.

SUBSYSTEMS=="usb",

ATTRS{idVendor}=="09fb",

ATTRS{idProduct}=="6010",

MODE="0666"

SUBSYSTEMS=="usb",

ATTRS{idVendor}=="09fb",

ATTRS{idProduct}=="6810",

MODE="0666"

◆

T-Core RISC-V BSP

After Quartus Prime and USB-Blaster II driver are installed, please download the T-Core RISC-V
BSP (TCORE-RISCV-FreedomE300.tar.gz) from the web (

http://T-Core.terasic.com/cd

). Then,

decompress the file using command: tar -zxvf TCORE-RISCV-FreedomE300.tar.gz. So far, you can
see TCORE-RISCV-FreedomE300 file. For more information about T-Core RISC-V BSP, please
refer following table.

Table 3-3 T-Core RISC-V BSP

file or folder

Description

Quartus_Project/TCORE_FreedomE
300

a Quartus Prime project, contains a RISC-V Core,
Freedom E300.

Quartus_Project/
TCORE_FreedomE300/V/Freedom_
E300_Wrapper.v

the top file of Freedom E300. User can use it to connect
to do logic operation, etc.

Toolchains

prebuilt tools for compiling and debugging programs.

freedom-e-sdk/bsp/drivers

contains some driver code, such as the underlying driver
code for PLIC modules, PRCI, etc.

freedom-e-sdk/bsp/include

contains header files for register address and parameter of
modules, such as SPI, UART, GPIO, etc.

freedom-e-sdk/bsp/libwrap

contains specific implementation of underlying library
functions related to the hardware platform.

freedom-e-sdk/bsp/env/freedom-e300
-terasic

contains Terasic T-Core board supported package.

freedom-e-sdk/software

contains demonstration for reference.

freedom-e-sdk/Makefile

the main Makefile for compilation and debug.

◆

Download a pof file to FPGA

Follow the procedures below to write RISC-V FPGA configure data into MAX10 internal flash.

Make sure SW2 is changed to correct location, set SW2.1=0 and SW2.2=1, as shown in

Figure 3-15

to ensure MAX10 is on JTAG chain, and RISC-V is off JTAG chain.

Summary of Contents for T-Core



































































Search results

Summary of Contents for T-Core

Reviews:

Related manuals for T-Core

Brands by name

Popular brands

Terasic T-Core, User Manual

Search results

Summary of Contents for T-Core

Reviews:

Related manuals for T-Core

Brands by name

Popular brands