Terasic ALTERA TR5-F40W User Manual Download Page 55

Page: 55 / 73

TR5-F40W

User

Manual

www.terasic.com

June 20, 2018

Power on the FPGA board.

Copy the “Demonstrations/PFL/flash_programming_batch” folder under the CD to your

PC’s local drive.

Execute the batch file flash_program_ub2.bat to start flash programming.

Power off the FPGA Board.

Set FPGA configure mode as FPPx32 Mode by setting SW7 MSEL[0:4] to 00010.

Specify configuration of the FPGA to Factory Hardware by setting the FACTORY_LOAD

dip in SW5 to the upper position.

Power on the FPGA Board, and the Configure Done LED should light.

Except for programming the Flash with the default code PFL, the batch file also writes PFL

(Parallel Flash Loader) Option Bits data into the address 0x30000. The option bits data specifies

0x20C0000 as start address of your hardware design.

The NIOS II EDS tool

nios-2-flash-programmer

programs the Flash based on the Parallel Flasher

Loader design in the FPGA. The Parallel Flash Loader design is included in the default code PFL

and the source code is available in the folder Demonstrations/ PFL in System CD.

Summary of Contents for ALTERA TR5-F40W










































































Search results

Summary of Contents for ALTERA TR5-F40W

Reviews:

Related manuals for ALTERA TR5-F40W

Brands by name

Popular brands

Terasic ALTERA TR5-F40W, User Manual

Search results

Summary of Contents for ALTERA TR5-F40W

Reviews:

Related manuals for ALTERA TR5-F40W

Brands by name

Popular brands