Teledyne Genie Nano Series User Manual Download Page 75

Page: 75 / 121

Nano Series GigE Vision Camera

Operational Reference

•

Event Control Category

The Genie Nano Event control, as shown by CamExpert, groups parameters used to configure

Camera Event related features. Parameters in gray are read only, either always or due to another

parameter being disabled. Parameters in black are user set in CamExpert or programmable via an

imaging application.
Features listed in the description table but tagged as Invisible are usually for Teledyne DALSA or

third party software usage—not typically needed by end user applications. Also important, Genie

Nano cameras are available in a number of models implementing different sensors and image

resolutions which may not support the full feature set defined in this category.

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands

Teledyne Genie Nano Series, User Manual

Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands