Teledyne Genie Nano Series User Manual Download Page 77

Page: 77 / 121

Nano Series GigE Vision Camera

Operational Reference

•

Off

Off The selected event is disabled.

On The selected event will generate a software event.

GigEVisionEvent

GigEVisionEvent The selected event will generate a software event.

This entry is deprecated.

Using "On" is recommended.

Event Statistic Selector

eventStatisticSelector

Selects which Event statistic to display.

1.00

Expert

DFNC

Image Lost

ImageLost Image is acquired but lost before it’s been

transferred.

Invalid Frame Trigger

InvalidFrameTrigger Counts the frame trigger occurring in an invalid

Trigger region.

Packet Resend Count

PacketResendCount Counts the number of packet resends.

Event Statistic Count

eventStatisticCount

Display the count of the selected Event.

1.00

Expert

DFNC

Event Statistic Count

Reset

eventStatisticCountReset

Reset the count of the selected Event.

1.00

Expert

DFNC

Frame Start Data

EventFrameStartData

Data of the frame start event

1.00

Guru

Frame Start Event ID

EventFrameStart

Represents the event ID to identify the

EventFrameStart software Event. (RO)

1.00

Guru

Frame Start Event

Timestamp

EventFrameStartTimestamp

Timestamp of the EventFrameStart event. (RO)

1.00

Guru

Exposure Start Event ID

EventExposureStart

Represents the event ID to identify the

EventExposureStart software Event. (RO)

1.00

Guru

Exposure Start Data

EventExposureStartData

Data of the exposure start event

1.00

Guru

Exposure Start Event

Timestamp

EventExposureStartTimestamp

Timestamp of the EventExposureStart event. (RO)

1.00

Guru

Exposure End Event ID

EventExposureEnd

Represents the event ID to identify the

EventExposureEnd software Event.

1.00

Guru

Exposure End Data

EventExposureEndData

Data of the exposure end event

1.00

Guru

Exposure End Event

Timestamp

EventExposureEndTimestamp

Timestamp of the EventExposureEnd event. (RO)

1.00

Guru

AcquisitionStartNextValid

Event ID

EventAcquisitionStartNextValid

Generate an event on acquisition start next valid.

1.00

Guru

Acquisition Start Next

Valid End Data

EventAcquisitionStartNextValidData Data of the acquisition start next valid event.

1.00

Guru

AcquisitionStartNextValid

Event Timestamp

EventAcquisitionStartNextValid

Timestamp

Timestamp of the acquisition start next valid

event. (RO)

1.00

Guru

Valid Frame Trigger Event

EventValidFrameTrigger

Generate an event on valid frame trigger.

1.00

Guru

Valid Frame Trigger Data

EventValidFrameTriggerData

Data of the valid frame trigger event.

1.00

Guru

Valid Frame Trigger Event

Timestamp

EventValidFrameTrigger

Timestamp

Timestamp of the Valid frame trigger event. (RO)

1.00

Guru

InvalidFrameTrigger Event

EventInvalidFrameTrigger

Generate an event on invalid frame trigger.

1.00

Guru

Invalid Frame Trigger

Data

EventInvalidFrameTriggerData

Data of the invalid frame trigger event.

1.00

Guru

InvalidFrameTrigger Event

Timestamp

EventInvalidFrameTrigger

Timestamp

Timestamp of the invalid frame trigger event. (RO)

1.00

Guru

ImageLost Event ID

EventImageLost

Generate an event on image lost.

1.00

Guru

Image Lost Data

EventImageLostData

Data of the image lost event

1.00

Guru

ImageLost Event

Timestamp

EventImageLostTimestamp

Timestamp of the image lost event. (RO)

1.00

Guru

Events Overflow Event ID

EventeventsOverflow

Represents the event ID to identify the

EventeventsOverflow software Event. (RO)

1.00

Guru

Event Overflow Data

EventeventsOverflowData

Data of the event overflow event

1.00

Guru

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands

Teledyne Genie Nano Series, User Manual

Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands