Teledyne Genie Nano Series User Manual Download Page 11

Page: 11 / 121

Nano Series GigE Vision Camera

Genie Nano Series Overview

•

Teledyne DALSA Development Software

Teledyne DALSA Software Platform for Microsoft Windows

Sapera LT version 8.01 or later (for Windows)

includes Sapera Network Imaging Package and GigE Vision Imaging

Driver, Sapera Runtime and CamExpert.

Provides everything you will need to develop imaging applications

Sapera documentation in compiled HTML help, and Adobe Acrobat® (PDF)

Available for download

http://www.teledynedalsa.com/imaging/support/

Sapera Processing Imaging Development Library

(available for Windows or Linux - sold separately):

Contact Teledyne DALSA Sales

Teledyne DALSA Software Platform for Linux

GigE-V Framework (for both X86 or Arm type processor)

Contact Teledyne DALSA Sales

Third Party GigE Vision Development

Third Party GigE Vision Software Platform Requirements

Support of GenICam GenApi version 2.3

General acquisition and control

Support of GenICam GenApi version 2.3

File access: firmware, configuration data, upload &

download

Support of GenICam XML schema version 1.1

GenICam™ support — XML camera description file

Embedded within Genie Nano

About GigE Vision

Genie Nano cameras are 100% compliant with the GigE Vision 1.2

specification which defines the communication interface protocol used by any

GigE Vision device. The device description and capabilities are contained in an

XML file. For more information see:

http://www.machinevisiononline.org/public/articles/index.cfm?cat=167

Genie Nano cameras implement a superset of the GenICam™ specification

which defines device capabilities. This description takes the form of an XML

device description file respecting the syntax defined by the GenApi module of

the GenICam™ specification. For more information see

www.genicam.org

The Teledyne DALSA GigE Vision Module provides a license free development platform for Teledyne

DALSA GigE hardware or Sapera vision applications. Additionally supported are Sapera GigE Vision

applications for third party hardware with the purchase of a GigE Vision Module license, or the

Sapera processing SDK with a valid license.
The GigE Vision Compliant XML device description file is embedded within Genie Nano firmware

allowing GigE Vision Compliant applications access to Genie Nano capabilities and controls

immediately after connection.

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Teledyne Genie Nano Series, User Manual, Page: 11 / 121

Search results

Summary of Contents for Genie Nano Series

Reviews: