Teledyne Genie Nano Series User Manual Download Page 78

Page: 78 / 121

•

Operational Reference

Nano Series GigE Vision Camera

Events Overflow Event

Timestamp

EventeventsOverflowTimestamp

Timestamp of the EventeventsOverflow event.

1.00

Guru

Gev Timestamp Latch

GevtimestampControlLatch

Latch the current timestamp internal counter value

in the timestampValue feature.

1.00

Invisible

Gev Timestamp Value

GevtimestampValue

Returns the 64-bit value of the timestamp counter.

1.00

Invisible

Gev Timestamp Tick

Frequency

GevtimestampTickFrequency

Indicates the number of timestamp ticks (or

increments) during 1 second (frequency in Hz).

1.00

Invisible

Gev Timestamp Reset

GevtimestampControlReset

Resets the timestamp counter to 0.

1.00

Invisible

Basic Exposure Events Overview

The following timing graphic shows the primary events related to a simple acquisition.

FrameActive

Frame Inactive

Exposure

ReadOut

Exposure

Delay

FrameStart Event

ExposureStart

Event

ExposureEnd

Event

FrameActive

TimeStamp Latch

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Teledyne Genie Nano Series, User Manual, Page: 78 / 121

Search results

Summary of Contents for Genie Nano Series

Reviews: