Teledyne Genie Nano Series User Manual Download Page 31

Page: 31 / 121

Nano Series GigE Vision Camera

Operational Reference

•

Device pane: View and select from any installed GigE Vision or Sapera acquisition device. After

a device is selected CamExpert will only present parameters applicable to that device.

•

Parameters pane: Allows viewing or changing all acquisition parameters supported by the

acquisition device. CamExpert displays parameters only if those parameters are supported by

the installed device. This avoids confusion by eliminating parameter choices when they do not

apply to the hardware in use.

•

Display pane: Provides a live or single frame acquisition display. Frame buffer parameters are

shown in an information bar above the image window.

•

Control Buttons: The Display pane includes CamExpert control buttons. These are:

Acquisition control button:

Click once to start live grab, click again to stop.

Single frame grab:

Click to acquire one frame from device.

Software trigger button:

With the I/O control parameters set to Trigger Enabled / Software Trigger

type, click to send a single software trigger command.

CamExpert display controls:

(these do not modify the frame buffer data)

Stretch (or shrink) image to fit, set image display to original size, or zoom

the image to any size and ratio. Note that under certain combinations of

image resolution, acquisition frame rate, and host computer speed, the

CamExpert screen display may not update completely due to the host CPU

running at near 100%. This does not affect the acquisition.

Histogram / Profile tool:

Select to view a histogram or line/column profile during live acquisition.

•

Output pane: Displays messages from CamExpert or the GigE Vision driver.

CamExpert View Parameters Option

All camera features have a Visibility attribute which defines its requirement or complexity. The

states vary from Beginner (features required for basic operation of the device) to Guru (optional

features required only for complex operations).
CamExpert presents camera features based on their visibility attribute and provides quick Visibility

level selection via controls below each Category Parameter list [ << Less More>> ]. The user can

also choose the Visibility level from the View ∙ Parameters Options menu.

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands

Teledyne Genie Nano Series, User Manual

Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands