Teledyne Genie Nano Series User Manual Download Page 34

Page: 34 / 121

•

Operational Reference

Nano Series GigE Vision Camera

UserSet 2

UserSet2 Select the User Defined Configuration space UserSet1

to save to or load from features settings previously

saved by the user.

Load Configuration

UserSetLoad Loads the camera configuration set specified by the

User Set Selector feature, to the camera and makes it

active. Can not be updated during a Sapera transfer.

(W)

Save Configuration

UserSetSave Saves the current camera configuration to the user

set specified by the User Set Selector feature. The

user sets are located on the camera in non-volatile

memory. (W)

Device Built-In Self Test

deviceBIST

Command to perform an internal test which will

determine the device status. (W)

1.00

Beginner

Device Built-In Self Test

Status

deviceBISTStatus

Return the status of the device Built-In Self test.

Possible return values are device-specific.

1.00

Beginner

Passed

No failure detected

1.00

DFNC

Beginner

Last firmware update

failed

FirmwareUpdateFailure

Last firmware update operation failed.

1.00

Beginner

Unexpected Error

Unexpected_Error Switched to recovery mode due to unexpected

software error.

Device Built-In Self Test

Status All

deviceBISTStatusAll Return the status of the device Built-In Self-Test as a

bitfield. The meaning for each bit is device-specific.

Device Reset

DeviceReset Resets the device to its power up state. (W)

Serial Number

DeviceID

Displays the device’s factory set camera serial

number.

1.00

Beginner

Power-up Configuration

Selector

UserSetDefault

Specify the camera configuration set to load and

make active on camera power-up or reset. The

camera configuration sets are stored in camera non-

volatile memory.

None

Keep Internal configuration.

1.00

Invisible

Factory Setting

Default

Select the Factory Setting values as the Power-up

Configuration.

1.00

Invisible

UserSet1

UserSet1 Select the user defined configuration UserSet 1 as the

Power-up Configuration.

UserSet2

UserSet2 Select the user defined configuration UserSet 2 as the

Power-up Configuration.

Calibration Date

deviceCalibrationDateRaw Date when the camera was calibrated.

Device Acquisition Type

deviceAcquisitionType Displays the Device Acquisition Type of the product.

Sensor

The device gets its data directly from a sensor.

1.00

DFNC

Invisible

Device TL Type

DeviceTLType

Transport Layer type of the device.

1.00

DFNC

Invisible

GigE Vision

GigEVision GigE Vision Transport Layer

Device TL Version Major

DeviceTLVersionMajor

Major version of the device’s Transport Layer.

1.00

Invisible

Device TL Version Minor

DeviceTLVersionMinor Minor version of the device’s Transport Layer.

userSetError

1.00

Invisible

NoError

No Error

1.00

Invisible

LoadGenericError

Unknown error

1.00

DFNC

LoadBusyError The camera is busy and cannot perform the action

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands

Teledyne Genie Nano Series, User Manual

Search results

Summary of Contents for Genie Nano Series

Reviews:

Related manuals for Genie Nano Series

Brands by name

Popular brands