Teledyne Genie Nano Series User Manual Download Page 20

Page: 20 / 121

•

Connecting the Genie Nano Camera

Nano Series GigE Vision Camera

Connectors

The Nano has two connectors:

•

A single RJ45 Ethernet connector for control and video data transmitted to/from the host

computer Gigabit NIC. The Genie Nano also supports

Power Over Ethernet

(PoE).

See Ruggedized RJ45 Ethernet Cables for secure cables.

•

A 10 pin I/O connector for camera power, plus trigger, strobe and general I/O signals. The

connector supports a retention latch, while the Nano case supports thumbscrews. Teledyne

DALSA provides optional cables (see Accessories). See 10-pin I/O Connector Details for

connector pin out specifications.

The following figure of the Genie Nano back end shows connector and LED locations. See

Mechanical Specifications for details on the connectors and camera mounting dimensions.

Status LED

10 Pin

I/O & Power

Ethernet Connector

(supports PoE)

Supports

Thumbscrew

Secured Cables

Camera Mounts

(4 sides)

Optional Tripod

Mount

Genie Nano – Rear View

Summary of Contents for Genie Nano Series


























































































































Search results

Summary of Contents for Genie Nano Series

Reviews:

Teledyne Genie Nano Series, User Manual, Page: 20 / 121

Search results

Summary of Contents for Genie Nano Series

Reviews: