Teledyne ADFM Hot Tap Installation And Operation Manual Download Page 28

Page: 28 / 116

ADFM® Flow Meter



Section 2 Setup and Installation

2-8

2.3 WinADFM Software

For complete information about setup a nd operation of
WinADFM software, refer to the WinADFM user manual.

2.3.1 Setup

The following section contains the basic steps for setting up a site
file and programming the ADFM. Basic data retrieval steps can
be found in Section 2.12. For complete programming and data
retrieval instructions, see the

WinADFM

software manual.

To begin setup and programming:

1. Start the

WinADFM

software. Create a Station file (appli-

cation programming file) by selecting File > New. Select
ADFM Station.

Figure 2-7 Creating a new Station file

2. Enter a Site ID with a maximum of 8 alphanumeric char-

acters, with no spaces or symbols, and save.

3. Select ADFM > Setup.

There are four tabs at the top of the window. Select each
tab and enter the programming information in each tab
window.

Summary of Contents for ADFM Hot Tap





















































































































Search results

Summary of Contents for ADFM Hot Tap

Reviews:

Teledyne ADFM Hot Tap, Installation And Operation Manual, Page: 28 / 116

Search results

Summary of Contents for ADFM Hot Tap

Reviews: