manualshive.com logo in svg

Teledyne ADFM Hot Tap, Installation And Operation Manual, Page: 97 / 116

Share
Download
Teledyne ADFM Hot Tap Installation And Operation Manual Download Page 97

ADFM® Flow Meter

Section 3  Maintenance and Troubleshooting

3-11

Figure 3-5 Canister controller: opening the electronics lid

2. The interior electronics are attached to the lid. Laying the 

controller on its side, very carefully ease the lid a few 
inches away from the case (Figure 3-6).
Wiring from the battery compartment is connected to the 
electronics. 

Do not attempt to pull the electronics all 

the way out of the case.

Ensure that the connections between the sensor interface board
and the motherboard are properly seated. There are two connec-
tions: a ribbon cable for VCC and grounding connections, and a
coaxial cable for transmission of the sensor’s analog signal.

Figure 3-6  Canister controller sensor interface board connections

Do not alter the connections made on the motherboard for any
reason other than to re-establish proper connection.

Allen 
screws (4)

Ribbon
cable

Coaxial

cable

Summary of Contents for ADFM Hot Tap





















































































































Reviews:

No comments