manualshive.com logo in svg

Teledyne ADFM Hot Tap, Installation And Operation Manual, Page: 99 / 116

Share
Download
Teledyne ADFM Hot Tap Installation And Operation Manual Download Page 99

A-1

ADFM® Flow Meter

Appendix A  Parts and Accessories

Parts and Accessories can be purchased by contacting Teledyne
Isco’s Customer Service Department. 

Teledyne Isco

Customer Service Department
P.O. Box 82531
Lincoln, NE 68501  USA

Phone: (800) 228-4373
(402) 464-0231
FAX:(402) 465-3022

E-mail:[email protected]

A.1 General Spare Parts 

and Accessories

ADFM control box  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-7100-005

ADFM canister controller . . . . . . . . . . . . . . . . . . . . . . 62-7110-005

ADFM IS control box . . . . . . . . . . . . . . . . . . . . . . . . . . 62-7100-105

ADFM IS canister controller . . . . . . . . . . . . . . . . . . . . 62-7110-105

Internal modem (for both box and canister) . . . . . . . . 60-7004-015

RS232 Communication cable, 3 m (10 ft). Connects PC with 9-pin
serial port with ADFM box, or ADFM canister with
Amp connectors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-7004-057

RS232 Communication cable, 3 m (10 ft). Connects PC with 9-pin
serial port with ADFM canister with
Crown connector  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-7004-027

DC power cable pigtail for ADFM box,
and ADFM canister with Amp connectors . . . . . . . . . 60-7004-062

DC power cable pigtail for ADFM canister
with Crown connectors  . . . . . . . . . . . . . . . . . . . . . . . . 60-7004-041

Flow meter suspension harness kit60-7109-002

Pro20 sensor with 15 m (49 ft) cable. . . . . . . . . . . . . . 60-7004-004

Pro20 sensor with 30 m (98 ft) cable. . . . . . . . . . . . . . 60-7004-005

Pro20 sensor with 45 m (147 ft) cable. . . . . . . . . . . . . 60-7004-006

Extension cable for Pro20 sensor, 15 m (49 ft) . . . . . . 60-7004-061

(Total cable length should not exceed 150 ft without prior
factory approval.)

Extension cable for Pro20 sensor, 30 m (98) ft . . . . . . 60-7004-013

(Total cable length should not exceed 150 ft without prior
factory approval.)

Summary of Contents for ADFM Hot Tap





















































































































Reviews:

No comments