Teledyne 300 Instruction Manual Download Page 85

Page: 85 / 111

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 79

BENCH HEAT

SHUTDOWN

Temperature control of

the Optical bench cannot

be maintained at its

48oC set point

Check Optical Bench

heater and thermistor as

described in Section 9.10

SAMPLE PRESSURE

WARNING

The Sample Pressure is

less than 15"Hg or is

greater than 35"Hg

Check for pressure

transducer problems as

described in Sect 10.6.5

and Sect 10.6.1

SAMPLE FLOW

WARNING

The sample flow is less

than 500 cc/min or

greater than 1000

cc/min.

Check for pneumatic

system problems as

described in Section

10.6.1 Check for flow

transducer problems as

described in Sect 10.6.5

BOX TEMP

WARNING

The inside chassis temp

is less than 10oC or is

greater than 50oC

See Section 10.6.2

SAMPLE TEMP

WARNING

The Sample

Temperature is less than

10oC or is greater than

50oC

See Section 10.6.2

CANNOT DYN ZERO

An offset of more than

+5 ppm would be

required to Zero adjust

the analyzer

See Section 10.5.5

CANNOT DYN SPAN

A slope of less than 0.5

or greater than 2.0 would

be required to Span

adjust the analyzer

See Section 10.5.6

V/F NOT

INSTALLED

The CPU is unable to

communicate with the

V/F Board

Check and re-seat CPU

and V/F board. See

Sect. 10.6.3

SYSTEM RESET

A power Off-On cycle

has occurred

None required

RAM INITIALIZED

Dynamic memory has

been re-initialized in

response to the

installation of a new

PROM or memory chip

None required

TABLE 10.1

Summary of Contents for 300
















































































































Search results

Summary of Contents for 300

Reviews:

Teledyne 300, Instruction Manual, Page: 85 / 111

Search results

Summary of Contents for 300

Reviews: