manualshive.com logo in svg

Teledyne 300, Instruction Manual, Page: 31 / 111

Share
Download
Teledyne 300 Instruction Manual Download Page 31

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 25

 

 

SYSTEM MODES 

Mode 

Meaning 

SAMPLE  x (1) 

Sampling normally 

SAMPLE  x (1) 

Flashing indicates adaptive filter is on 

ZERO CAL x (2) 

Doing a zero check or adjust 

SPAN CAL x (2) 

Doing a span check or adjust 

MP CAL 

Doing a multi-point calibration 

SETUP  xxx (3) 

Configuring analyzer (sampling continues) 

DIAG DAS (4) 

Data Acquisition configuration 

DIAG I/O (4) 

Test digital I/O signals 

DIAG AOUT (4) 

Test analog output channels 

DIAG D/A (4) 

Configure and Calibrate Digital to Analog converters 

DIAG TCHN (4) 

Configure Test Channel output 

(1) x = A (auto) 

(2)  x = M (manual), A (auto), R (remote) 

(3) xxx = software revision (e.g. A.9) 

(4) diagnostic test modes  

TABLE 2.2  

The message field shows test measurements or warning messages.  Tables 2.3 and 2.4 
summarize the test measurements and warning messages and their meanings.  Refer to 
Sections 4.0 and 5.0 for detailed information on viewing test measurements and warning 
messages and clearing warnings. 

TEST MEASUREMENTS 

Test Message 

Meaning 

TIME=xx:xx:xx Current 

time-of-day 

(HH:MM:SS) 

RANGE=xxxx PPM 

Analog output full-scale range 

STABIL=x.xxx PPM 

Standard Deviation of CO readings 

CO MEAS=xxxxx MV 

Current V/F measure channel (mV) 

CO REF=xxxxx MV 

Current V/F reference channel (mV) 

MR RATIO=X.XXX 

Ratio of the Reference and Measure values 

PRES=xxx IN-HG-A 

Absolute sample pressure - inches Hg 

SAMPLE FL=xxx CC/M 

Sample flow through Analyzer (cc/min) 

SAMPLE TEMP=xxx C 

Temperature in the absorption cell 

BENCH TMP=xxx C 

Optical Bench Temperature 

WHEEL TMP=xxx C 

Filter Wheel Temperature 

BOX TEMP=xxx C 

Internal box temperature (degrees C) 

DCPS=xxxxxx MV  

DC power supply (mV) 

SLOPE=x.xxx 

Internal formula - Slope  

OFFSET=xx.x MV 

Internal formula - Offset 

TABLE 2.3  

 

Summary of Contents for 300
















































































































Reviews:

No comments