Teledyne 300 Instruction Manual Download Page 50 | Manualshive

Page: 50 / 111

Teledyne 300 Instruction Manual Download Page 50

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 44

Triggering Events

Name

Description

ATIMER

Automatic timer expired

EXITZR

Exit zero calibration

EXITSP

Exit span calibration

EXITMP

Exit multi-point calibration

SLPCHG Slope

changed

REPORT PERIOD
This property specifies the period between reports (DAS entries). Enter the number of
days and press

ENTR

. Then enter the number of hours (the leftmost digits) and minutes

and press

ENTR

.

NUMBER OF RECORDS
This property specifies how many records you want to store in this data channel. Each
record consists of a time stamp and the sampled measurements from each parameter. The
memory of the M300 has capacity for a total of about 8,000 records (for

all

data

channels). When the specified number of records for a data channel has been reached,
the channel will “wrap around”, with the oldest records being overwritten with the newest
records.

Enter the number of records desired and press

ENTR

. Only when you press

ENTR

is

the data file actually deleted. If you press

EXIT

the property will not be modified and

data file will not be deleted.

RS-232 REPORT
This property controls printing of reports on the RS-232 channel. If set to ON then every
time a new report is stored it’s also printed on the RS-232 channel. If this property is set
to OFF, the reports are still stored in the data file, but not printed on the RS-232 channel.

PARAMETERS
This property shows the

number

of parameters being sampled. Each data channel can

sample up to 10 parameters, each with a separate sampling mode.
This parameter also specifies the

mode

of data collection. When sampling a reading such

as a concentration at periodic intervals, it is desirable to use the

AVG mode

to generate an

average of the readings during the interval. But when sampling the concentration when

NOTE

Changing this property requires that any existing data records

be deleted because memory must be re-initialized.

«
...
48
49
50
51
52
...
»

Summary of Contents for 300
















































































































Reviews:

No comments