manualshive.com logo in svg

Teledyne 300, Instruction Manual, Page: 48 / 111

Share
Download
Teledyne 300 Instruction Manual Download Page 48

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 42

 

 

4.11.2 Setting-up Data Channels 

To setup a new data channel or modify an existing data channel, press 

SETUP-DAS-

EDIT

 to get into the DAS edit mode. 

 
Once in the DAS edit mode, definitions of data channels may be created or modified by 
using the MENU buttons described in the following table: 
 

Data Channel Edit Menu 

Button 

Description 

PREV 

Moves to the previous data channel 

NEXT 

Moves to the next data channel 

INS 

Inserts a new data channel in front of the current 

one (allowed up to 20 data channels) 

DEL 

Deletes the current data channel (prompts first) 

EDIT 

Edits the properties of the current data channel 

PRNT 

Prints a summary of all of the data channel on the 

RS-232 port 

 

The creation or modification of data channel definitions is accomplished by modifying 
the 

properties

 of existing (or default) channel definitions.  The table below lists all of the 

properties defined for data channels. 

Summary of Contents for 300
















































































































Reviews:

No comments