Teledyne 300 Instruction Manual Download Page 33

Page: 33 / 111

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 27

ILLUSTRATION OF NORMAL DISPLAY

FIGURE 2.2

TEST

is pushed, the upper center display cycles through the menu of test parameters,

e.g. Sample flow (see Table 2.3). If

CALZ

is pushed, the sequence of operations for

setting the Analyzer zero is initiated(see Section 3.1).

If

CALS

is pushed, the sequence of operations for setting

SPAN

is initiated (see Section

3.1).

CAL

is used to initiate span setting using sample gas, such as during a formal

calibration.

Pushing

MSG

will cause a message to appear on the upper center display.

Pushing

CLR

will erase a message, provided the condition causing the message has

ceased.

Pushing

SETUP

changes the function of the push buttons and is used for setting basic

parameters as described in Section 4.0.

2.2.3 Status LED’s

The three status

LED’s

to the right of the display indicate the general status of the Model

300 Analyzer. The green

SAMPLE LED

indicates the sampling status. The yellow

CAL LED

indicates the calibration status. The red

FAULT LED

indicates the fault

status. Table 2.5 summarizes the meanings of the status

LED’s

Summary of Contents for 300
















































































































Search results

Summary of Contents for 300

Reviews:

Teledyne 300, Instruction Manual, Page: 33 / 111

Search results

Summary of Contents for 300

Reviews: