Teledyne 300 Instruction Manual Download Page 51 | Manualshive

Page: 51 / 111

Teledyne 300 Instruction Manual Download Page 51

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 45

exiting calibration it is desirable to take a single instantaneous reading using the

INST

mode

. The table below summarizes the available sampling modes.

Sampling Modes

Mode

Description

INST Records

instantaneous

reading

AVG

Records average reading during reporting interval

MIN

Records minimum reading during reporting interval

MAX

Records maximum reading during reporting interval

Each parameter in this list can refer to a different (or the same) point, and can use a
different (or the same) sampling mode. For instance, you could create three parameters
which all measure the CO concentration for range 1 (the CONC1 parameter), but which
use the MIN, AVG, and MAX sampling modes. This permits you to record not only the
average concentration during the reporting interval, but the maximum excursions as well.

Like data channels, parameters also have properties which are listed in the table below.

Parameter Properties

Property

Description

Initial

Setting

Setting Range

PARAMETER

The parameter to sample

CONC1

Any of the parameters
listed in the table of
parameters shown
above

SAMPLE
MODE

The sampling mode to use
when reading this
parameter

AVG

Any one of the INST,
AVG, MIN, and MAX.

PRECISION

Number of decimal digits

1

0 - 3

The table below lists the data parameters initially defined. The entries in the Name and
Units columns are visible when editing and printing the data channel properties.

«
...
49
50
51
52
53
...
»

Summary of Contents for 300
















































































































Reviews:

No comments