Teledyne 300 Instruction Manual Download Page 32 | Manualshive

Page: 32 / 111

Teledyne 300 Instruction Manual Download Page 32

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 26

WARNING MESSAGES

Warning Message

Meaning

SYSTEM RESET

Issued whenever Analyzer is powered on

RAM INITIALIZED

RAM was erased (incl. DAS reports)

SOURCE WARNING

IR source < 2500 OR >= 5000 mV

BENCH HEAT SHUTDOWN

Optical bench temp control not working

SAMPLE FLOW WARNING

Sample flow < 500 cc/m or > 1000 cc/m

SAMPLE PRESSURE WARN

Sample pressure < 15 or > 35 In-Hg-A

SAMPLE TEMP WARNING

Sample temperature < 10

°

C or > 50

°

C

BOX TEMP WARNING

Box temp. < 12

°

C or > 48

°

C

BENCH TEMP WARN

Optical Bench < 43

°

C or > 53

°

C

WHEEL TEMP WARN

Filter Wheel < 63

°

C or > 73

°

C

CANNOT DYN ZERO

CO offset < -1500 or > +1500 mV

CANNOT DYN SPAN

CO slope < 0.5 or > 2.0

V/F NOT INSTALLED

A/D - I/O card not installed or bad

SYNC ERROR

No modulation on detector output

TABLE 2.4

The menu field changes depending on the mode of the Analyzer and the buttons that have
been pressed. It indicates the current function of each of the 8 push buttons below the
display. See Section 2.2.2 for information on using the push buttons.

2.2.2 Programmable push buttons

The 8 push buttons below the display are programmable by the CPU in that their
functions change depending on the mode of the Analyzer or the operations being
performed. The legend above a button identifies its current function. If there is no
legend above a button, it has no function and will be ignored if pressed.

«
...
30
31
32
33
34
...
»

Summary of Contents for 300
















































































































Reviews:

No comments