TELEDYNE API T300 Operation Manual Download Page 332

Page: 332 / 347

APPENDIX A-3: Warnings and Test Functions

Teledyne API - T300/T300M and M300E/EM 04906J DCN7122

A-12

TEST FUNCTION NAME

MESSAGE TEXT

DESCRIPTION

COOFFSET2

OFFSET2=0.000

CO OFFSET2=0.000

CO offset for range #2 in dual range
mode, computed during zero/span
calibration.

CO2SLOPE

CO2 SLOPE=1.000

slope, computed during zero/span

calibration.

CO2OFFSET

CO2 OFFSET=0.000

offset, computed during zero/span

calibration.

O2SLOPE

O2 SLOPE=0.980

slope, computed during zero/span

calibration.

O2OFFSET

O2 OFFSET=1.79 %

offset, computed during zero/span

calibration.

CO=17.7 PPM

CO concentration for current range.

CO2

CO2=15.0 %

concentration.

O2=0.00 %

concentration.

TESTCHAN

TEST=1751.4 MV

Value output to

TEST_OUTPUT

analog

output, selected with

TEST_CHAN_ID

variable.

CLOCKTIME

TIME=09:52:20

Current instrument time of day clock.

RANGE(s)

User Configurable

CO2RANGE

CO2 RANGE=20 %

range.

O2RANGE

O2 RANGE=100 %

range.

STABILITY

STABIL=0.0 PPM

CO STB=0.0 PPM

1, 2

CO2 STB=0.0 %

O2 STB=0.0 %

Concentration stability (standard deviation
based on setting of

STABIL_FREQ

and

STABIL_SAMPLES

COMEAS

CO MEAS=4125.0 MV

Detector measure reading.

COREF

CO REF=3750.0 MV

Detector reference reading.

MRRATIO

MR RATIO=1.100

Measure/reference ratio.

SAMPPRESS

PRES=29.9 IN-HG-A

Sample pressure.

SAMPFLOW

SAMP FL=751 CC/M

Sample flow rate.

SAMPTEMP

SAMPLE TEMP=26.8 C

Sample temperature.

BENCHTEMP

BENCH TEMP=48.1 C

Bench temperature.

WHEELTEMP

WHEEL TEMP=68.1 C

Wheel temperature.

O2CELLTEMP

O2 CELL TEMP=50.2 C

sensor cell temperature.

BOXTEMP

BOX TEMP=26.8 C

Internal chassis temperature.

PHOTOTEMP

PHT DRIVE=2500.0 MV

Photometer temperature.

COSLOPE

SLOPE=1.000
CO SLOPE=1.000

CO slope for current range, computed
during zero/span calibration.

COSLOPE1

SLOPE1=1.000
CO SLOPE1=1.000

CO slope for range #1 in dual range
mode, computed during zero/span
calibration.

COSLOPE2

SLOPE2=1.000
CO SLOPE2=1.000

CO slope for range #2 in dual range
mode, computed during zero/span
calibration.

COOFFSET

OFFSET=0.000
CO OFFSET=0.000

CO offset for current range, computed
during zero/span calibration.

COOFFSET1

OFFSET1=0.000
CO OFFSET1=0.000

CO offset for range #1 in dual range
mode, computed during zero/span
calibration.

COOFFSET2

OFFSET2=0.000
CO OFFSET2=0.000

CO offset for range #2 in dual range
mode, computed during zero/span
calibration.

CO2SLOPE

CO2 SLOPE=1.000

slope, computed during zero/span

calibration.

CO2OFFSET

CO2 OFFSET=0.000

offset, computed during zero/span

calibration.

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands

TELEDYNE API T300, Operation Manual

Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands