Triggering
222PS Operator Manual
3Ć67
Motor Trigger Function
The motor trigger function responds to pulse bursts such as those
produced by uninterruptable power supplies (UPS) and variableĆfreĆ
quency motor drives. This function triggers on the first pulse that
occurs in each burst if the interval between the bursts is at least
2.5 ms. If the interval between bursts is less than 2.5 ms, the motor
trigger function does not operate.
The motor trigger function also reduces noise on 50/60 Hz line signals
resulting in cleaner triggering in noisy line environments.
The trigger source, slope, level, and mode functions still operate
normally when you select MOTOR TRIG. Note, however, that even
though the trigger source selections include EXT, motor trigger does
not work with signals applied to the EXT TRIG INPUT.
Triggering on Motor Drive Signals
To trigger on the variableĆfrequency signal that drives a motor, use the
following procedure:
ĂĂStep 1:ă
Toggle MOTOR TRIG on and set the trigger level midway
between the top and bottom of the desired pulse group.
ĂĂStep 2:ă
Set the trigger slope to
+
for pulse groups separated by
a low" region (Figure 3Ć34). Set the trigger slope to
-
if the
region separating the pulse groups is high" (Figure 3Ć35).
ĂĂStep 3:ă
Use normal trigger mode if the oscilloscope has trouble
triggering on a slow motor speed.
Triggering on 50/60 Hz Line Signals
To trigger on 50/60 Hz line signals, toggle MOTOR TRIG on and set
the other trigger controls to trigger either on the rising edge or the
falling edge of the waveform. The motor trigger function suppresses
stray trigger signals that result from line transients and noise.
Triggering
222PS Operator Manual
3Ć67
Motor Trigger Function
The motor trigger function responds to pulse bursts such as those
produced by uninterruptable power supplies (UPS) and variableĆfreĆ
quency motor drives. This function triggers on the first pulse that
occurs in each burst if the interval between the bursts is at least
2.5 ms. If the interval between bursts is less than 2.5 ms, the motor
trigger function does not operate.
The motor trigger function also reduces noise on 50/60 Hz line signals
resulting in cleaner triggering in noisy line environments.
The trigger source, slope, level, and mode functions still operate
normally when you select MOTOR TRIG. Note, however, that even
though the trigger source selections include EXT, motor trigger does
not work with signals applied to the EXT TRIG INPUT.
Triggering on Motor Drive Signals
To trigger on the variableĆfrequency signal that drives a motor, use the
following procedure:
ĂĂStep 1:ă
Toggle MOTOR TRIG on and set the trigger level midway
between the top and bottom of the desired pulse group.
ĂĂStep 2:ă
Set the trigger slope to
+
for pulse groups separated by
a low" region (Figure 3Ć34). Set the trigger slope to
-
if the
region separating the pulse groups is high" (Figure 3Ć35).
ĂĂStep 3:ă
Use normal trigger mode if the oscilloscope has trouble
triggering on a slow motor speed.
Triggering on 50/60 Hz Line Signals
To trigger on 50/60 Hz line signals, toggle MOTOR TRIG on and set
the other trigger controls to trigger either on the rising edge or the
falling edge of the waveform. The motor trigger function suppresses
stray trigger signals that result from line transients and noise.
Summary of Contents for 222PS
