background image

Introduction

2001989-301A- draft 1

ApexPro™

1-13

CAUTION

POWER REQUIREMENTS — Before connecting the device to the 
power line, check that the voltage and frequency ratings of the 
power line are the same as those indicated on the unit's label. If this 
is not the case, do not connect the system to the power line until you 
adjust the unit to match the power source.

In the U.S.A., if the installation of this equipment will use 240 V 
rather than 120V, the source must be a center-tapped, 240V, single-
phase circuit. 

This equipment is suitable for connection to public mains as defines 
in CISPR 11. 

CAUTION

RESTRICTED SALE — U.S. federal law restricts this device to sale 
by or on the order of a physician.

CAUTION

SECURITY — The web browser which runs in conjunction with the 
ApexPro server is intended for hospital INTRANET use only. If 
confidential patient information is made available from the hospital 
intranet, the security of the data is the responsibility of the hospital.

CAUTION

SUPERVISED USE — This equipment is intended for use under the 
direct supervision of a licensed health care practitioner.

CAUTION

UNINTENTIONAL RADIO FREQUENCY (RF) 
INTERFERENCE — Unintentional RF interference could degrade 
the reliability and performance of the wireless data link. The facility 
must maintain an RF environment free from unintentional 
interference. Refer to the service manuals for more information.

CAUTION

VENTILATION REQUIREMENTS — Set up the device in a 
location which affords sufficient ventilation. The ventilation 
openings of the device must not be obstructed. The ambient 
conditions specified in the technical specifications must be ensured 
at all times.

Draft

Summary of Contents for ApexPro




























Reviews: