Tektronix 1710J Series, Instruction Manual

Page: 249 / 252

Index
1710J-Series Waveform Monitors
Index–5
HV Osc and Error Amp, 5–19
Power Supply Outputs, 5–20
Z-Axis Amplifier, 5–21
Low Voltage Power Supply, Diagram 7, 5–17
Error Amplifier, 5–19
Feedback Transformer Driver and Peak Detector,
5–19
Line Rectifier and Filter, 5–17
Output Filters, 5–19
Output Under-Voltage Shutdown, 5–19
Pulse Width Modulator, 5–18
Microcontroller, Diagram 5, 5–13
LED Drive, 5–16
Processor, 5–13
RGB Amplifier, 5–15
Overview, 5–1
Sweep Generators and Horiz Output, Diagram 4,
5–12
Horizontal Output Amplifier, 5–13
Magnifier Amplifier, 5–13
Sweep Generator, 5–12
Timing, Diagram 3, 5–9
Graticule Illumination, 5–11
Horizontal Sync Generator, 5–10
Regulators, 5–11
Timing State Machine, 5–9
Trace Rotation, 5–11
Vertical Sync Generator, 5–11
Z-Axis Control, 5–11
Vertical Input, Diagram 1, 5–3
Calibrator, 5–6
Channel Switch, 5–4
External Sync Input and Source Switch, 5–4
Filter Selection, 5–6
Input Amplifiers, 5–4
Sync Stripper, 5–5
Vertical Output, Diagram 2, 5–7
Gain Cell, 5–7
Gain Cell Amplifier, 5–7
Second DC Restorer, 5–7
Switchable Gain Amplifier, 5–8
Vertical Output Amplifier, 5–9
Timing, Diagram 3
Graticule Illumination, 5–11
Horizontal Sync Generator, 5–10
Regulators, 5–11
Timing State Machine, 5–9
Trace Rotation, 5–11
Vertical Sync Generator, 5–11
Z-Axis Control, 5–11
Trace Rotation Control, 2–3
Troubleshooting, 8–17
Foldout Pages, 8–17
Adjustment Locations, 8–18
Assembly and Circuit Numbering, 8–18
Circuit Board Illustrations, 8–18
Diagrams, 8–17
Parts Locating Charts, 8–18
General Troubleshooting Techniques, 8–20
High Voltage Power Supply, 8–26
CRT Voltage Check, 8–28
Focus Amplifier Check, 8–26
Grid Drive Check, 8–27
High Voltage Oscillator Check, 8–27
Preliminary Checks, 8–26
Z-Axis Amplifier Check, 8–26
Low Voltage Power Supply, 8–23
Control Circuit Check, 8–25
Error Amplifier Check, 8–25
Output Check, 8–24
Preliminary Checks, 8–23
Rectifier/Switcher Check, 8–24
Major Assembly Interconnection, 8–19
Parts Lists, 8–18
Replaceable Electrical Parts, 8–18
Replaceable Mechanical Parts, 8–19
Specific Troubleshooting Techniques, 8–22
Power Supply Troubleshooting, 8–22
Typical Description, 1–2
V
V Cal, 2–3
Verification Procedure
Check Calibrator Amplitude, 6–10
Check Calibrator Frequency, 6–4
Check Chrominance Filter Response, 6–15
Check DC Restorer Operation, 6–10
Check Flat Response, 6–12
Check Low Pass Filter Response, 6–14
Check Power Supply Operation, 6–4
Check Return Loss, 6–15
Check RGB/YRGB Parade Display, 6–8
Check Sweep Calibration, 6–6
Check Sweep Operation, 6–5
Check Sync Separation, 6–4
Check Transient Response, 6–13
Check Vertical Gain, 6–9
Check X5 Transient Response, 6–14
Preliminary Setup, 6–3
Vertical Calibration Adjust, 2–3
Vertical Input, Diagram 1
Calibrator, 5–6
Channel Switch, 5–4