background image

TECNOEKA Srl _____________________________________________________________ use and instruction manual 

page. 6 __________________________________________________________________________________________ 

1.3  Technical specifications 

 

External overall dimension L x D x H 

935 x 980 x 1388  mm 

Weight 

152 Kg 

Nominal thermal capacity 

17,50  kW 

Tray maximal load (GN1/1) 

4  kg 

Total load (10 trays GN 1/1) 

44  kg 

ISO 7-1 gas union 

1/2 “ 

Water union 

3/4 “ 

Fume exhaustion vertical tube 

Ø 150 mm; height

 

min. 1000 mm 

Appliance category (for Danimarca) 

II2H3B/P 

Factory adjustment 

Methane gas G20 , 20 mbar 

Type of construction 

B

11 

 / B

21

 

Electrical power 

220-230  V ~ 

Electrical capacity  

0,7  kW 

 

Class 

I  

Power cable type 

 H07RN-F 3 x 1,5 mm

Connecting electric cable 

Type Y 

Gas connection pressure 

Liquid butane/propane gas G30/G31 : 28-30 mbar 

Methane gas G20: 20 mbar 

Water connection pressure 

Max. 200 kPa (2,0 bar) 

Gas consumption calculated at low heat value of H

i

 at 

15° and 1013 mbar 

G30 : 1,380 kg / h 

G20 : 1,852 m

3

 / h 

Parameters to the chimney B

11

 (Ø 150 mm, L=1 m)  

(G20  20 mbar) 

fume load 

31.63 g/s 

fume temperature 

136.8 °C 

fume pressure 

-2.1 Pa 

Parameters to the chimney B

11

 (Ø 150 mm, L=1 m)  

(G30  28-30 mbar) 

fume load 

29.60 g/s 

fume temperature 

141.6 °C 

fume pressure 

-2.3 Pa 

Main injector diameter 

G30/G31 :   220 

1/100 mm

 

G20 :   320 

1/100 mm

 

Primary air bush adjustment 

G30/G31 :   36 mm 

G20 :   24 mm 

Table 1 

 

The noise level of the appliance in operation is less than 70 dB (A).

 

 

2.  General instruction (for installation technician) 

The  installation  technician  must  make  sure  that  start-up  conforms  to  current  national 
regulations.  The  appliance  must  be  installed  only  by  qualified  personnel  authorised  by  the 
manufacturer.  She  must  observe  the  safety  regulations  in  force  in  the  country  where  the 
appliance is installed. All extraordinary maintenance jobs (possible adaptation to another type of 
gas  or  replacement  of  parts)  must  be  performed  by  qualified  personnel  having  the  necessary 
professional qualifications. The protected devices and / or sealed by the manufacturer and that 
are  not  intended  for  maintenance,  adjustment,  or  adaptation  to  change  of  gas  must  not  be 
handled either by the installer or user. The seals that must be removed to change the gas must 
be  restored  at  the  end  of  the  adaptation.  The  manufacturer  will  not  respond  for  damage  to 
people,  animals  and  property  due  to  installation  errors.  Likewise  the  manufacturer  is  not 
responsible for breakage caused to the appliance by incorrect installation. 

 

2.1  Storage 
If the appliance has been stored in a warehouse at a temperature below 0°C (min. allowed is –
5°C), it should be brought to a temperature of at least +10°C before it is turned on. 

 

2.2  Transporting the oven 
During  transport,  the  appliance  must  be  left  in  its  original  wooden  cage  to  protect  it  against 
damage. 

 

2.3  Unpacking the oven 
Remove all the packaging before installation, which is formed of a wooden pallet that holds the 
appliance and cardboard casing to protect it. Check that the appliance has not been damaged 
during  transport  and  if  any  damage  is  discovered  immediately  inform  your  retailer  and/or  the 
haulier. 

Summary of Contents for EKF 1064G E UD





























Reviews: