Taylor C801 Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 70

background image

1

C801/C801R/F802/P802/C803/C803R/C804

To the Installer

Section 1

To the Installer

The following are general installation instructions.
For complete installation details, please see the
check out card.

Installer Safety

In all areas of the world, equipment should

be installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.

Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.

S

Only Taylor authorized service personnel
should perform installation and repairs on
the equipment.

S

Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.

S

Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.

S

Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.

The main power supply(s) to the equipment

must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts as well as poor
performance or damage to the equipment.

Note: All repairs must be performed by an
authorized Taylor Service Technician.

This unit has many sharp edges that can

cause severe injuries.

Electrical Connections

Electrical connections to the grill must be provided
and arranged by Wendy's, with their preferred
licensed electrician. This must be completed
immediately following grill installation and prior to the
grill Start Up and Checkout by the local Taylor
representative.

Check the data plate on the grill for voltage, cycle,
phase and electrical specifications. The power
connections are located behind the access cover of
the control box under the front staging side of the
grill.

In the United States, this equipment is intended to
be installed in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70-1987. The
purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.
Compliance therewith and proper maintenance will
result in an installation essentially free from hazard!
In all other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.

The Proper Wire Size and Branch Circuit
Overcurrent Device shall be selected according to
the data label information and in accordance with
CEC Part I 2006, Section 14-100(e)(i). Incoming
power must be connected to the line side of the
power contactor.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

«
...
3
4
5
6
7
...
»

Summary of Contents for C801







































































Reviews:

No comments

Related manuals for C801

Sainbury's 956/4657

Brand: Argos Pages: 9

Brand: Fein Pages: 149

Brand: BeefEater Pages: 7

Brand: Ingersoll-Rand Pages: 51

Brand: NORDIC SEASON Pages: 12

Brand: Fri-Jado Pages: 32

Brand: Hitachi Koki Pages: 17

Brand: TriStar Pages: 5

Brand: Hitachi Pages: 28

Brand: Beko Pages: 32

Brand: Beko Pages: 29

Brand: Beko Pages: 64

Brand: Beko Pages: 48

Brand: Beko Pages: 7

UniFlame NBC3121D

Brand: Uniflame Pages: 28

Brand: Ryobi Pages: 3

Brand: Ryobi Pages: 84

Brand: Ryobi Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands