Taylor C801 Operating Instructions Manual Download

Page: 41 / 70

C801/C801R/F802/P802/C803/C803R/C804

Troubleshooting Guide

The following information is from the Wendy's Troubleshooting Guide (part no. 064274). The “Checklist Before
Calling the Taylor Company Call Center” indicates the symptoms and appropriate action to take. The “After Hours
Service Call Protocol” lists the questions to expect when calling 877-222-7010 after 10:00 pm Central Time and
on weekends.

Checklist Before Calling the Taylor Company Call Center

SYMPTOM

CHECK

ACTION TO TAKE

Raw, Undercooked or
Overcooked, Burned
Patties

a. Interference between platen or other object

(back splash, lane divider, release clips).

a. Install parts correctly to remove

obstructions.

b. Space between platen and grill surface to

appear equal all the way around platen.

b. If gap is visibly unequal,

Call for Service

c. Proper size patty (2 oz./4 oz.) placed under

correct platen.

c. Insure consistent use of the proper size

patties.

d. Patties spaced and positioned correctly to

insure full coverage by platen front, back
and sides.

d. Insure consistent, correct orientation and

placement of patties.

e. Meat temperature before laying patties

-40

F (1.1

C - 4.4

C) as stored.

e. Only use meat stored within the proper

pre-cook temperature range.

f. Any residue or carbon build-up on grill

surface.

f. Water scrape more frequently.

g. Release sheet condition.

g. Replace if worn or has pinholes.

h. Any residue or carbon build up on platen

surface behind sheet.

h. Insure daily cleaning procedures are

thoroughly and consistently followed.

i. Cook a full test run under adjustable and

corresponding fixed platen.

i. Compare same size patty from each platen.

If significantly different visually,

Call for

Service.

j. From full test run take internal meat

temperatures following operations manual
procedures (insure thermometer is
accurate).

j. If temperatures 185

F - 200

F (85

C -

C), no grill adjustment to be made.

Escalate to supervisor. If temperature is
below 175

F (79

C),

Call for Service

Cook Cycle Won't Start
(timing bar does not
display)

Is display green with meat size displayed?

a. If yes, does display change to timing bar

when platen is closed?

a. Normal operation, no action required.

b. If no, or timing bar does not display.

b. Press & Hold button five seconds. If normal

green display appears, close platen to start
cook cycle. If not, insure grill has preheated
for 30 minutes.

Call for Service.

Platen Closed and Will
Not Open

a. Is there a timer being displayed?

a. Let timing finish before proceeding.

b. Press & Hold button five seconds.

b. If platen won't open, and Up Arrow is

displayed, large font text or small font text,
note which and

Call for Service.

Summary of Contents for C801







































































Search results

Summary of Contents for C801

Reviews:

Related manuals for C801

Brands by name

Popular brands

Taylor C801, Operating Instructions Manual

Search results

Summary of Contents for C801

Reviews:

Related manuals for C801

Brands by name

Popular brands