tayco Scene Installation Manual Download Page 40

Page: 40 / 50

Find the location of the studs with

a stud finder; make marks on the

wall.

Mark the location of the wooden

cleat on the wall and position it to
the previously marked studs. The
recommended height is 54-inches

from the floor to the bottom of the
wooden cleat. Use the following
size as a guide for mounting the
wooden cleats on the wall listed in

Figure 1.

Level the wooden cleat and

attach it to studs with #10, 3-inch

wood screws, (Figure 2).

overhead storage - attachment
to dry wall with wood studs

WOODEN CLEAT

WOOD STUDS

#10-3 INCH
WOOD SCREW

WALL

FIGURE 1

WOODEN

CLEAT

DRY WALL

HANGING RAIL

ATTACHED TO HUTCH

(ALREADY INSTALLED)

WOOD STUD

54-INCHES FROM THE

FLOOR TO BOTTOM OF

THE WOODEN CLEAT

FIGURE 2

STORAGE

SIZE

WOODEN

CLEAT SIZE

36"

32"

42"

38"

48"

44"

54"

50"

60"

56"

66"

62"

72"

68"

40 Scene

MARCH 2016

Summary of Contents for Scene



















































Search results

Summary of Contents for Scene

Reviews:

Related manuals for Scene

Brands by name

Popular brands

tayco Scene, Installation Manual

Search results

Summary of Contents for Scene

Reviews:

Related manuals for Scene

Brands by name

Popular brands