tayco Scene Installation Manual Download Page 41

Page: 41 / 50

Hang the hutch over the installed

wooden cleat.

Secure with #10, 3-inch wood
screws from the inside back
panel of the hutch through the

wooden cleat, (Figure 3).

FIGURE 3

overhead storage - attachment
to dry wall with wood studs (cont'd)

tools & hardware needed

drill

It is the owner's responsibility to ensure that the wall type

and construction is of sufficient strength to carry the loads of

the overhead storage unit and its contents. Failure of the wall

to support all imposed loads may result in property damage

and/or personal injury. When in doubt, the use of other

methods of storage such as freestanding storage units,

hutches and bookcases is strongly recommended.

WARNING

#10-3"
wood screw

stud finder

torpedo level

measuring

tape

NOTES:

> use 6 screws for hutches w/o

dividers (48-inches and 54-inches

wide) and 8 screws for hutches
with dividers (60-inches, 66-inches

and 72-inches wide).

> make sure no electrical wires are

on the way of the screws.

#2 Robertson

long bit

41 Scene

MARCH 2016

Summary of Contents for Scene



















































Search results

Summary of Contents for Scene

Reviews:

Related manuals for Scene

Brands by name

Popular brands

tayco Scene, Installation Manual

Search results

Summary of Contents for Scene

Reviews:

Related manuals for Scene

Brands by name

Popular brands