manualshive.com logo in svg

Tatu Marchesan RCP2 1500, Operator'S Manual

Share
Download
Tatu Marchesan RCP2 1500 Operator'S Manual Download Page 8

6

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

RCP² 1500

To the operator

• Only trained and qualified personnel are allowed to operate the equipment.
• While working or during transportation, only the presence of the operator is 

allowed in the tractor.

• Do not allow children to play or to get over the equipment while it is operating, 

during transportation or storage.

• Have full knowledge of the soil before starting to work. Use the speed which 

is suitable to the conditions of the ground or pathways to be covered. Provide 

the delineation of obstacles or hazardous locations.

• Use personal protective equipment (PPE).
• Wear appropriate clothes and footwear. Avoid clothes that are either loose or 

hanging from the body, which may become entangled in moving parts.

• Never operate the equipment without its 

protective devices

.

• Wear protective gloves to work near the cutting parts.
• When lifting or lowering the equipment, check if there are no people or animals 

close or under it.

• Never attempt to change the adjustments, clean or lubricate the equipment 

while it is moving.

• In case of emergency, know how to stop the tractor and equipment quickly.
• Always shut down the engine, remove the key and use the handbrake before 

leaving the tractor seat.

• Only pull the equipment using a tractor with appropriate power.
• Carefully check the transport width on narrow locations.
• Do not drive the equipment under the influence of alcohol or any soothing/

stimulating medicine, as it may result in a serious accident.

• Do not allow people or animals to get under the equipment at any time.
• Whenever you unhitch the equipment, either in the field or shed, do it on a 

flat and firm surface. Make sure that the equipment is properly supported.

• We suggest that you carefully read the manual, as it will be a guide for 

periodic verifications that need to be done and will allow that you assure the 

maintenance of your equipment.

• In case of a fire outbreak or any possible hazard, the operator must leave the 

area as fast as possible and look for a safe place. Always have emergency 

numbers in hands.

• If there is any doubt after reading it, ask your dealer. For more complicated 

operations, there will be the right person to help you there.

• Please check the general safety instructions on the back cover of this manual.

Summary of Contents for RCP2 1500



































Reviews:

No comments

Brands by name

Popular brands

Load more brands