manualshive.com logo in svg

Tatu Marchesan RCP2 1500, Operator'S Manual

Share
Download
Tatu Marchesan RCP2 1500 Operator'S Manual Download Page 13

11

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

RCP² 1500

Data sheet

Model: .............................................................................................................

RCP² 1500

Cutting width (mm):................................................................................................... 1480

Number of blades: ........................................................................................................ 02

Cutting height (adjustable) - Minimum: ...................................................................... 40 m

 

- Maximum: .................................................................140 mm

Hitching type: .....................................................................(Three-point hitch) Category II

 ...........................................................................................  (PTO) 540 rpm

Blades rotation (540 rpm at the PTO): ................................................................ 1038 rpm

Tractor required power (cv): .......................................................................................... 50

Width (mm): .............................................................................................................. 2650

Length (mm): ............................................................................................................ 1600

Height (mm): ............................................................................................................. 1150

Weight (kg): ................................................................................................................ 568

RCP² 1500

The rotary cutter is designed for agricultural use only and it must not 

be used in urban areas.
Do not allow that people get closer during operation.

ATTENTION

Summary of Contents for RCP2 1500



































Reviews:

No comments

Brands by name

Popular brands

Load more brands