manualshive.com logo in svg

Tatu Marchesan RCP2 1500, Operator'S Manual

Share
Download
Tatu Marchesan RCP2 1500 Operator'S Manual Download Page 17

15

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

RCP² 1500

Set-up instructions

1/3

1/3

2/3

2/3

Correct assembly

Correct assembly

Aligned internal forks

Aligned internal forks

Incorrect assembly

Incorrect assembly

Unaligned internal forks

Unaligned internal forks

• Decrease the length of both protective covers, using the 

cut tubes as a measure and clean the cut residues.

• After that, assemble the cardan according to the assembly 

instructions on the following page.

• When using another tractor to work with the equipment, 

verify the length of the cardan shaft again.

NOTE The contact surface between the hub and the bar shall not be smaller than 1/3 of 

the total length.

When assembling the cardan shaft, it is necessary to be careful and leave the terminals 

on both ends aligned. The discrepancy of the terminals in 90° will cause vibrations and a 

greater wear on the universal joints, reducing the lifetime of the set.

When coupling the cardan to the tractor PTO, fasten the chain on a fixed point 

of the tractor so that the cardan shaft cover do not turn and do not get loose 

during maneuvers.

NOTE

Summary of Contents for RCP2 1500



































Reviews:

No comments

Brands by name

Popular brands

Load more brands