manualshive.com logo in svg

Tatu Marchesan RCP2 1500, Operator'S Manual

Share
Download
Tatu Marchesan RCP2 1500 Operator'S Manual Download Page 25

23

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

RCP² 1500

Lubrication points - lubricate daily

Maintenance

Lubrication

Check the tightening of the nuts and bolts and the conditions of pins and cotter pins 

daily.

The maintenance of the distributors and gearboxes is done as follows:
• When starting working and every day of the first week, check the oil level through the 

level marker and fill it up if necessary.

• Then, check the oil level monthly.
• Clean the grease fittings and apply a sufficient amount of new grease. Regarding the 

blade hubs, use only one of the greases on the table below.

• Change the oil every 

600

 worked hours or every one (1) year of use.

NOTE Do not pour oil over the level limit.

The oil volume on the double 

distributor is 1.9 liters and 2.34 

liters on each gearbox.
Use SAE 90 oil only.

Manufacturer

Specification

FL-Lubricantes Tutela Alfa 2K grease

Castrol

EPL 2 grease

Shell

Alvania EP(LF) 2 grease

Ipiranga

Ipiflex EP 2 grease

Ipiranga

Litholine EP 2 grease

Texaco

Multifak EP2 grease

Lubricate the points shown above and all grease fittings as well.

NOTE

Summary of Contents for RCP2 1500



































Reviews:

No comments

Brands by name

Popular brands

Load more brands