TANDBERG E5780 Reference Manual Download Page 39

Page: 39 / 298

Reference Guide: evolution 5000 E5780 and E5782 Encoder

Page 3-1

ST.RE.E10135.4

Chapter 3

Options and Upgrades

Contents

3.1

What’s Available................................................ 3-5

3.1.1

Hardware Options .................................. 3-5

3.1.2

Limitations on Number of Option
Modules ................................................. 3-5

3.1.3

Limitations on Use of Option Modules ... 3-6

3.1.4

How to See Which Options are
Fitted/Enabled........................................ 3-6

3.1.5

Software Options ................................... 3-6

Purchasable Software Options for
Standard Definition Mode ...................... 3-6

Purchasable Software Options for
High Definition Mode.............................. 3-6

3.1.6

Enabled Software Options ..................... 3-7

3.2

Basic Interoperable Scrambling System -
BISS (M2/EDCOM2/BISS) ................................ 3-8

3.3

Additional Audio and Linear PCM Option
(M2/EOM2/AUDLIN2) ....................................... 3-8

3.3.1

Overview................................................ 3-8

3.3.2

Assembly ............................................... 3-9

Rear Panel ............................................. 3-9

Audio In Connector ................................ 3-9

3.3.3

Technical Specification ........................ 3-10

3.4

Advanced Audio Coding Option
(M2/EOM2/ADVAUD)...................................... 3-11

3.4.1

Overview.............................................. 3-11

3.4.2

Assembly ............................................. 3-11

Rear Panel ........................................... 3-11

AES x Connector ................................. 3-11

AES REF Connector ............................ 3-12

3.5

Remux Option (M2/EOM2/REMUX)................ 3-13

3.5.1

Overview.............................................. 3-13

3.5.2

Assembly ............................................. 3-13

Rear Panel ........................................... 3-13

DVB ASI IN 1, 2 and 3 Connectors ...... 3-14

DVB ASI OUT 1 Connector.................. 3-14

3.5.3

Technical Specification ........................3-14

Connectors...........................................3-14

LEDs ....................................................3-15

3.6

SMPTE 310 (SSI) and ASI Optical Outputs
Option Modules (M2/EOM2/ASI-OPT) and
(M2/EOM2/SSI-US).........................................3-16

3.6.1

Overview ..............................................3-16

3.6.2

Assembly .............................................3-16

Rear Panel ...........................................3-16

SMPTE 310 1, 2 and 3 Connectors......3-17

ASI OUT 1, 2 Connectors ....................3-17

3.7

ATM Network Interface Option Module
(M2/EOM2/ATMS155_…) ...............................3-18

3.7.1

Overview ..............................................3-18

3.7.2

Assembly .............................................3-18

3.7.3

Common Connectors ...........................3-18

DVB-ASI Copper Input .........................3-18

DVB-ASI Copper Output ......................3-19

10BaseT Ethernet Connector...............3-19

3.7.4

Technical Specification ........................3-19

Variants of The ATM Network
Interface Module ..................................3-19

DVB-ASI Copper Output ......................3-20

DVB-ASI Copper Input .........................3-20

10BaseT Ethernet Connector...............3-20

Multi-mode Fibre Optic Connector .......3-21

Monomode Fibre Optic Connector .......3-21

M2/EOM2/ATMS34 PDH/E3
Connector ............................................3-22

M2/EOM2ATMS45 PDH/DS3
Connector ............................................3-23

M2/EOM2ATMS155E STM-1
Electrical Module..................................3-23

3.8

STM-1 OC3 Multi-mode Physical Interface
Module (M2/EOM2/ATMS155MM) ..................3-24

3.8.1

Assembly .............................................3-24

Summary of Contents for E5780











































































































































































































































































































Search results

Summary of Contents for E5780

Reviews:

Related manuals for E5780

Brands by name

Popular brands

TANDBERG E5780, Reference Manual

Search results

Summary of Contents for E5780

Reviews:

Related manuals for E5780

Brands by name

Popular brands