TANDBERG E5780 Reference Manual Download Page 295

Page: 295 / 298

Alarm List

Reference Guide: evolution 5000 E5780 and E5782 Encoder

Page L-5

ST.RE.E10135.4

Alarm Id

Alarm Name

Alarm Description Level

Source

Module

00000225

No SET_RATE
Messages Received

No Reflex bitrate messages received in the last 2 seconds

Alarm

Video Encoder

00000226

SET_RATE Messages
Expired

PCR time stamp for the Reflex bitrate message received occurs in
the past.

Alarm Video

Encoder

00000280

Module Fault

Applies to the Motherboard modules only. The audio module has
failed to boot.

Alarm

Audio A

00000281

Comms Error

"Not set in normal operation. For use with MEM controller, to force a
new config download as a result of an error."

Alarm

Audio A

00000282

Config Update

The audio module is not responding correctly to the requested
config.

Alarm

Audio A

00000284

Incorrect Parameters

One or more parameters are incorrect.

Alarm

Audio A

00000285

PCR Error

Unable to read the internal PCR count.

Alarm

Audio A

00000286

Silence Timeout Left

The audio level of the left channel was below the silence threshold
longer than the programmed timeout.

Alarm

Audio A

00000287

Silence Timeout Right

The audio level of the right channel was below the silence threshold
longer than the programmed timeout.

Alarm

Audio A

00000288

Level Clipping Left

The audio level of the left channel is above the clipping threshold.

Alarm

Audio A

00000289

Level Clipping Right

The audio level of the right channel is above the clipping threshold.

Alarm

Audio A

00000290

Embedded Source 1

The embedded audio input source is missing.

Alarm

Audio A

00000291

Embedded Source 2

The embedded audio input source is missing.

Alarm

Audio A

00000292

Embedded Source 3

The embedded audio input source is missing.

Alarm

Audio A

00000293

Embedded Source 4

The embedded audio input source is missing.

Alarm

Audio A

00000294

AC-3 Input Invalid

No input stream when the coding is Dolby digital AC-3 pass-thru.

Alarm

Audio A

00000295

No Digital Input

Too many errors on the digital audio input.

Alarm

Audio A

00000296

Mux FIFO Overflow

Error on the internal Mux input. The audio channel will be reset.

Alarm

Audio A

00000297

Duplicate PID

The selected PID value clashes with another.

Alarm

Audio A

00000298

Invalid PID

The selected PID value is out of range.

Alarm

Audio A

00000299

Mux Bitrate too low

The output bitrate is too low. The audio output will be switched off.

Alarm

Audio A

00000300

Audio Un-Calibrated

The analog audio input is not calibrated.

Alarm

Audio A

00000301

Lip Sync Error

The requested delay exceeds the maximum value allowed for the
current coding standard and hardware.

Alarm

Audio A

00000302

Invalid Sampling Rate

The sampling frequency is incompatible with the coding mode Dolby
digital AC-3 pass-thru.

Alarm

Audio A

00000303

ADS Input Invalid

Unable to detect valid MPEG-2/Audio Descriptor Service on input.

Alarm

Audio A

00000304

DTS Input Invalid

Unable to detect a valid DTS Audio stream on input.

Alarm

Audio A

00000305

Wrong Dolby
Standard

Encoder is set to Dolby Digital Plus but the audio input is Dolby
Digital or vice versa

Alarm Audio

00000320 Module

Fault

Applies to the Motherboard modules only. The audio module has
failed to boot.

Alarm

Audio B

00000321

Comms Error

"Not set in normal operation. For use with MEM controller, to force a
new config download as a result of an error."

Alarm

Audio B

00000322

Config Update

The audio module is not responding correctly to the requested
config.

Alarm

Audio B

00000324

Incorrect Parameters

One or more parameters are incorrect.

Alarm

Audio B

00000325

PCR Error

Unable to read the internal PCR count.

Alarm

Audio B

00000326

Silence Timeout Left

The audio level of the left channel was below the silence threshold
longer than the programmed timeout.

Alarm

Audio B

00000327

Silence Timeout Right

The audio level of the right channel was below the silence threshold
longer than the programmed timeout.

Alarm

Audio B

Summary of Contents for E5780











































































































































































































































































































Search results

Summary of Contents for E5780

Reviews:

Brands by name

Popular brands

TANDBERG E5780, Reference Manual

Search results

Summary of Contents for E5780

Reviews:

Brands by name

Popular brands