manualshive.com logo in svg

TANDBERG E5780, Reference Manual

Share
Download
TANDBERG E5780 Reference Manual Download Page 224

  

Technical Specification 

Page B-14 

Reference Guide: evolution 5000 E5780 and E5782 Encoder 

 

ST.RE.E10135.4 

B.4.6 RS-422 

Data 

This provides an RS-422 synchronous, serial communications data input interface.  

Table B.21: RS-422 Data Specification 

Item  

Specification 

Safety status 

SELV 

Type 

ITU-T V.11 (RS-422), synchronous serial data and external clock 

Connector designation 

RS-422 DATA 

Connector type 

15-way D-type female  

Clock frequencies 

n x 64 kbit/s from 64 kbit/s to 2048 kbit/s (selectable) 

 or 

n x 56 kbit/s from 56 kbit/s to 1792 kbit/s (selectable) 

Time stamp 

Not supported 

Operation modes 

Bit-pipe - Transport packet alignment and byte alignment relative to the incoming bitstream 
are arbitrary. 

Summary of Contents for E5780











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands