manualshive.com logo in svg

TANDBERG E5780, Reference Manual

Share
Download
TANDBERG E5780 Reference Manual Download Page 61

  

Options and Upgrades 

Reference Guide: evolution 5000 E5780 and E5782 Encoder 

Page 3-23 

ST.RE.E10135.4 

M2/EOM2ATMS45 PDH/DS3 Connector 

The M2/EOM2ATMS45 PDH/DS3 module comprises S11365. 

Table 3.26: DS3, G.703 Input Connector 

Item Specification 

Connector Type 

75 

Ω

 BNC, female 

Connector Designation 

ATM-PDH-DS3 IN 

Data rate 

44.736

 

Mbit/s

 

Data Coding 

BZD3 

Physical/Electrical Characteristics 

ITU-T G.703 

Jitter Tolerance 

ITU-T G.823 

Loss of Signal Detect 

ITU-T G.775 

Over-voltage Protection 

ITU-T G.703 Annex B DS3 and E3 

ATM Direct Cell Mapping 

ITU-T G.804 

PLCP Mapping 

ETSI T/NA(91) and T/NA(91)18 

Supported Frame Modes 

ITU-T G.751 and ITU-T G.832. 

Transmit Timing Source 

Recovered Clock or Local Clock 

Table 3.27: DS3, G.703 Output Connector 

Item Specification 

Connector Type 

75 

Ω

 BNC, female 

Connector Designation 

ATM-PDH-DS3 OUT 

Data rate 

44.736

 

Mbit/s

 

Data Coding 

BZD3 

Physical/Electrical Characteristics 

ITU-T G.703 

Jitter Tolerance 

ITU-T G.823 

Over-voltage Protection 

ITU-T G.703 Annex B 

ATM Direct Cell Mapping 

ITU-T G.804 

PLCP Mapping 

ETSI T/NA(91) and T/NA(91)18 

Supported Frame Modes 

ITU-T G.751 and ITU-T G.832. 

Transmit Timing Source 

Recovered Clock or Local Clock 

M2/EOM2ATMS155E STM-1 Electrical Module 

The M2/EOM2ATMS45 PDH/DS3 module comprises S11367. 

Summary of Contents for E5780











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands