9
English
If situations occur which are not covered in this manual, take care and
use common sense. Contact Tanaka dealer if you need assistance.
Pay special attention to statements preceded by the following words:
WARNING
Indicates a strong possibility of severe personal injury or loss of
life, if instructions are not followed.
CAUTION
Indicates a possibility of personal injury or equipment damage, if
instructions are not followed.
NOTE
Helpful information for correct function and use.
SPECIFICATIONS
Model
TCS27EPAP (S)
Engine Size (cm
3
)
26.9
Spark plug
CHAMPION CJ6
Fuel tank capacity (cm
3
)
520
Chain Oil Tank Capacity (cm
3
)
160
Dry Weight (kg)
(Without guide bar and chain)
5.8
Guide bar length (mm)
250
Chain pitch (mm)
9.52
Chain gauge (mm)
1.09
Sound pressure level LpA (dB (A)) by ISO 22868
Equivalent
Uncertainty
89
3
Sound power level LwA (dB (A)) by ISO 22868
Measured
Uncertainty
Sound power level LwA (dB (A)) by 2000/14/EC
Measured
Guaranteed
105
3
108
111
Vibration level (m/s
2
) by ISO 22867
Front
handle
Rear
handle
Uncertainty
4.9
9.2
1.0
Max. engine power by ISO 8893 (kW)
0.9
Max. engine speed (min
-1
)
11000
Idle engine speed (min
-1
)
3000
NOTE:
Equivalent noise level / vibration levels by ISO 11680 are calculated as the time-weighted energy total for noise / vibration levels under
various working conditions with the following time distribution: 1/2 idle, 1/2 racing speed.
* All data subject to change without notice.
ASSEMBLY PROCEDURES
Drive shaft to engine (Fig. 1)
Loosen tube locking bolt (1) about ten turns so that the bolt point
will not obstruct drive shaft tube to be inserted. When inserting drive
shaft tube, hold the tube locking bolt outward preventing inside
fi
tting
from obstructing as well.
Insert the drive shaft into the clutch case of the engine properly until
the marked position (2) on the drive shaft tube meets the clutch case.
NOTE
When it is hard to insert drive shaft up to the marked position on
the drive shaft tube, turn drive shaft by the cutter mounting end
clockwise or counter-clockwise. Tighten tube locking bolt lining
up the hole in the shaft tube. Then tighten clamp bolt securely.
Cutting attachment to drive shaft (Fig. 2)
Loosen tube locking bolt (3).
Insert the drive shaft into the gear case of the attachment properly
until the marked position (4) on the drive shaft tube meets the gear
case.
Installation of handle (Fig. 3)
Attach the handle to the drive shaft tube with the angle towards the
engine.
Adjust the location to the most comfortable position before operation.
Throttle wire / stop cord
Press the upper tab (6) and open the air cleaner cover. (
Fig. 4
)
Connect stop cords. (
Fig. 5
)
If the throttle outer end (7) is threaded on your unit, screw it and the
earth terminal (8) (if so equipped) into the cable adjuster stay (9) all
the way, and then tighten this cable end using the adjuster nut (10)
against the cable adjuster stay (9).
Connect throttle wire end (11) to carburetor (12) and install swivel
cap (13) (if so equipped) where is included in tool bag, onto swivel
(12) (
Fig. 6
).
Some models may come with the parts installed.
WARNING
Never try to start engine without side case securely fastened.
NOTE
When assembling brand new unit, take o
ff
and discard a piece of
cardboard (14) between gear case and side case. (
Fig. 7
)
000Book̲TCS27EPAP(S)̲WE.indb 9
000Book̲TCS27EPAP(S)̲WE.indb 9
2014/06/04 15:21:58
2014/06/04 15:21:58